CURTAIN SHIELD AIRBAG ASSEMBLY DISPOSAL

CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS component, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.

Tech Tips

When scrapping a vehicle equipped with the SRS or disposing of a steering pad, deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the SERVICE DEPT. of the DISTRIBUTOR.

CAUTION:

A airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with bare hands to discharge static electricity before performing this procedure.
Never dispose of a curtain shield airbag assembly that has an undeployed airbag.
The airbag emits an exploding sound when it is deployed, so perform the operation outdoors, and where it will not create a nuisance to nearby residents.
When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool). Perform the operation in a place away from electrical noise.
When deploying the airbag, perform the operation at least 10 m (33 ft.) away from the curtain shield airbag assembly.
The curtain shield airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
Use gloves and safety glasses when handling a curtain shield airbag assembly with a deployed airbag.
Do not apply water, etc. to a curtain shield airbag assembly with a deployed airbag.
Always wash your hands with water after completing the operation.

PROCEDURE

DISPOSE OF CURTAIN SHIELD AIRBAG ASSEMBLY (When Installed in Vehicle)
Tech Tips

Prepare a auxiliary battery as the power source to deploy the airbag.
1. Check the function of SST.
  
  SST
  
  09082-00700
  
  CAUTION:
  
  Always use the specified SST (SRS Airbag Deployment Tool) when deploying the airbag.
  1. Text in Illustration
    
    *1 Auxiliary Battery
    
    Connect the red clip of SST to the positive auxiliary battery terminal and the black clip of SST to the negative auxiliary battery terminal.
  2. Press the SST activation switch, and check that the LED on the SST activation switch illuminates.
    
    CAUTION:
    
    Do not connect the SST connector (yellow colored one) to the airbag.
    
    If the LED illuminates when the activation switch is not pressed, SST may be malfunctioning. Do not use SST.
  3. Disconnect SST from the auxiliary battery.
2. Remove the roof headlining Click here.
3. Text in Illustration
  
  *1 Protective Tape
  
  *2 Locking Button
  
  Using a screwdriver with its tip wrapped with protective tape, release the locking button.
  
  Note
  
  Do not damage the airbag wire harness when handling the airbag connector.
4. Disconnect the airbag connector.
5. Text in Illustration
  
  *1 Locking Button
  
  Connect SST.
  
  SST
  
  09082-00700
  
  09082-00802 ( 09082-10801, 09082-20801 )
  1. After connecting SST, connect it to the curtain shield airbag assembly.
    
    Note
    
    Do not lock the secondary lock of the twin lock to avoid damaging the SST connector and wire harness.
  2. Text in Illustration
    
    *1 Auxiliary Battery
    
    Move SST to at least 10 m (33 ft.) away from the vehicle.
  3. Close all doors and windows of the vehicle.
    
    Note
    
    Do not damage the SST wire harness.
  4. Connect the red clip of SST to the positive auxiliary battery terminal and the black clip of SST to the negative auxiliary battery terminal.
6. Deploy the curtain shield airbag assembly.
  1. Check that no one is inside the vehicle or within a 10 m (33 ft.) radius of the vehicle.
  2. Press the SST activation switch and deploy the curtain shield airbag assembly.
    CAUTION:
    
    When deploying the curtain shield airbag assembly, make sure that no one is near the vehicle.
    
    The curtain shield airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
    
    Use gloves and safety glasses when handling a curtain shield airbag assembly which has been deployed.
    
    Do not apply water etc. to a curtain shield airbag assembly with a deployed airbag.
    
    Always wash your hands with water after completing the operation.
    Tech Tips
    
    The airbag is deployed as the LED on the SST activation switch illuminates.

Text in Illustration
*1	Auxiliary Battery

Text in Illustration
*1	Protective Tape
*2	Locking Button

Text in Illustration
*1	Locking Button

Text in Illustration
*1	Auxiliary Battery

DISPOSE OF CURTAIN SHIELD AIRBAG ASSEMBLY (When not Installed in Vehicle)

Tech Tips

Prepare a auxiliary battery as the power source to deploy the airbag.

Check the function of SST.

SST

09082-00700

CAUTION:

Always use the specified SST (SRS Airbag Deployment Tool) when deploying the airbag.
1. Text in Illustration
  
  *1 Auxiliary Battery
  
  Connect the red clip of SST to the positive auxiliary battery terminal and the black clip of SST to the negative auxiliary battery terminal.
2. Press the SST activation switch, and check that the LED on the SST activation switch illuminates.
  CAUTION:
  
  Do not connect the SST connector (yellow colored one) to the airbag.
  
  If the LED illuminates when the activation switch is not pressed, SST may be malfunctioning. Do not use SST.
3. Disconnect SST from the auxiliary battery.
Remove the curtain shield airbag assembly Click here.
Text in Illustration

*a Cut

Cut off the deployment section of the curtain shield airbag assembly.
Using a T25 "TORX" socket wrench, remove the screw.
Text in Illustration

*1 Locking Button

Connect SST.

SST

09082-00802 ( 09082-10801, 09082-20801 )
1. After connecting SST, connect it to the curtain shield airbag assembly.
  
  Note
  
  Do not lock the secondary lock of the twin lock to avoid damaging the SST connector and wire harness.

Text in Illustration
*1	Auxiliary Battery

Text in Illustration
*a	Cut

Text in Illustration
*1	Locking Button

Using a braided wire harness, tie the curtain shield airbag assembly to the tire.

Text in Illustration
*a	Stripped Wire Harness Section

Stripped wire harness section

Area	Measurement
A	1.25 mm²or more (0.00192 in.²or more)

CAUTION:

Do not use a wire harness that is too thin or any other object to tie the curtain shield airbag assembly because it may snap due to the shock when the airbag is deployed. Always use a wire harness for vehicle use with a cross section of at least 1.25 mm²(0.0019 in.²).

Tech Tips

To calculate the area of the stripped wire harness cross section:

Area = 3.14 x (Diameter)²divided by 4

Position the curtain shield airbag assembly inside the tire, as shown in the illustration.

Tire size

Area	Measurement
A	185 mm (7.28 in.)
B	360 mm (14.17 in.)

CAUTION:

Make sure that the wire harnesses are tight. If there is any slack in the wire harnesses, the curtain shield airbag assembly may become loose due to the shock when the airbag is deployed.

Note

The tire may be damaged by the airbag deployment, so use unneeded tire.

Place the tires.

Text in Illustration

*1 Tire (2 or more)

CAUTION:

Do not place the curtain shield airbag assembly with the deployment direction facing toward the ground.
1. Place at least 2 tires under the tire to which the curtain shield airbag assembly is tied.
2. Place at least 2 tires over the tire to which the curtain shield airbag assembly is tied. The disc wheel should be installed onto the top tire.
  Note
  - Do not place SST connector under the tire because it could be damaged.
  - The disc wheel and tires may be damaged by the airbag deployment, so use unneeded disc wheel and tires.
3. Tie the tires together with 2 wire harnesses.
  
  CAUTION:
  
  Make sure that the wire harnesses are tight. It is highly dangerous when a loose wire harness results in the tires coming free due to the shock when the airbag is deployed.
Text in Illustration

*1 Auxiliary Battery

Connect SST.

SST

09082-00700

Note

To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the tire.
Deploy the curtain shield airbag assembly.
1. Connect the red clip of SST to the positive auxiliary battery terminal and the black clip of SST to the negative auxiliary battery terminal.
2. Check that no one is within a 10 m (33 ft.) radius of the tire to which the curtain shield airbag assembly is tied.
3. Press the SST activation switch and deploy the airbag.
  
  CAUTION:
  
  Make sure that no one is near the tire when deploying the airbag.
  
  Tech Tips
  
  The airbag is deployed as the LED on the SST activation switch illuminates.
Text in Illustration

*1 Plastic Bag

Dispose of the curtain shield airbag assembly.
CAUTION:
- The curtain shield airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
- Use gloves and safety glasses when handling a curtain shield airbag assembly which has been deployed.
- Always wash your hands with water after completing the operation.
- Do not apply water, etc. to a curtain shield airbag assembly which has been deployed.
1. Remove the curtain shield airbag assembly from the tire.
2. Place the curtain shield airbag assembly in a plastic bag, tie it tightly and dispose of it according to local regulations.