PUSH-BUTTON START, Diagnostic DTC:B2286

DTC Code DTC Name
B2286 Runnable Signal Malfunction

DESCRIPTION

This DTC is stored when a malfunction is detected in the READY signal circuit inside the power management control ECU.

Tech Tips

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2286 READY signal error inside the power management control ECU (1-trip detection logic*)

  • AM2 fuse

  • Power management control ECU

  • Harness or connector

 Turn the power switch on (IG) and wait 20 seconds or more.

Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The power source mode does not change to on (READY). -
Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2286

    Power Source Control

  • Ready Signal

 -

WIRING DIAGRAM

A01V22HE11
*a from Auxiliary Battery
*b Power Management Control ECU

CAUTION / NOTICE / HINT

Note


  • When using the GTS with the vehicle power switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

  • The push-button start uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting Click here.

  • Before replacing the power management control ECU, refer to the push-button start precaution Click here.

  • After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.

  • Inspect the fuses of circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (POWER SOURCE)


    1. A01V0DQE02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Power Management Control ECU)

      Disconnect the power management control ECU connectors.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      F55-1 (AM22) - Body ground Power switch off 11 to 14 V
      F56-7 (AM21) - Body ground Power switch off 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

    OK

  2. CHECK HARNESS AND CONNECTOR (GROUND)

    A01V1P6E02
    Text in Illustration
    *a

    Front view of wire harness connector

    (to Power Management Control ECU)

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F55-5 (E01) - Body ground Always Below 1 Ω
      F55-6 (E1) - Body ground Always Below 1 Ω
      F56-5 (E02) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK FOR DTC


    1. Clear the DTCs Click here.

    2. Turn the power switch on (IG).

    3. After 25 seconds have elapsed, check if the DTC has been output again.

      OK
      DTC B2286 is not output.

    OK

    END (USE SIMULATION METHOD TO CHECK) Click here

    NG

    REPLACE POWER MANAGEMENT CONTROL ECU Click here