ENTRY AND START SYSTEM(for Start Function) OPERATION CHECK


  1. OPERATION DESCRIPTION


    1. Push-button start function:


      1. When the electrical key transmitter sub-assembly is in a detection area inside the vehicle and the brake pedal is depressed, the hybrid control system is started by pressing the power switch.

      2. When the electrical key transmitter sub-assembly is in a detection area inside the vehicle and the brake pedal is not depressed, the power source mode is changed by pressing the power switch. The power source mode changes in the following order every time the power switch is pressed: off → on (ACC) → on (IG) → off.

      3. A004FN9C01
        *a Entry Indicator
        *b Power on display

        After getting into the vehicle while carrying the electrical key transmitter sub-assembly when the power switch is off, if the power switch is pressed while not depressing the brake pedal, the power source mode changes to on (ACC) and the entry indicator in the combination meter assembly blinks green*1 or "Power on" is displayed*2.


        • *1: except TFT Meter Type

        • *2: for TFT Meter Type

      4. A004FN9C01
        *a Entry Indicator
        *b Power on display

        After getting into the vehicle while carrying the electrical key transmitter sub-assembly when the power switch is off, if the power switch is pressed 2 times without depressing the brake pedal, the power source mode changes to on (IG) and the entry indicator in the combination meter assembly blinks green*1 or "Power on" is displayed*2.


        • *1: except TFT Meter Type

        • *2: for TFT Meter Type

      5. A004F02C08
        *a Entry Indicator
        *b Entry Warning Light display

        After getting into the vehicle while carrying the electrical transmitter sub-assembly when the power switch is off, if the brake pedal is depressed while the shift lever is in P or N, or the entry indicator in the combination meter assembly illuminates green*1 or the entry warning light is displayed*2.


        • *1: except TFT Meter Type

        • *2: for TFT Meter Type

      6. The hybrid control system starts if the power switch is pressed when the entry indicator in the combination meter assembly illuminates green*1 or the entry warning light is displayed*2.


        • *1: except TFT Meter Type

        • *2: for TFT Meter Type

    2. Changing the power source mode when the electrical key transmitter sub-assembly does not operate correctly due to wave interference or transmitter battery depletion:


      1. Unlock the door using the built-in mechanical key and get into the vehicle while carrying the electrical key transmitter sub-assembly.

      2. While depressing the brake pedal and facing the logo side of the electrical key transmitter sub-assembly towards the power switch, hold the electrical key transmitter sub-assembly near the power switch.

      3. A buzzer in the combination meter assembly sounds and the power source mode changes to on (IG). Pressing the power switch without depressing the brake pedal turns the power source mode from on (IG) to off.

    3. Starting the hybrid control system when the electrical key transmitter sub-assembly does not operate correctly due to wave interference or transmitter battery depletion:


      1. Unlock the door using the built-in mechanical key and get into the vehicle while carrying the electrical key transmitter sub-assembly.

      2. While depressing the brake pedal with the shift lever in P, while facing the logo side of the electrical key transmitter sub-assembly towards the power switch, hold the electrical key transmitter sub-assembly near the power switch.

      3. A buzzer in the combination meter assembly sounds, the power source mode changes to on (IG) and the entry indicator in the combination meter assembly illuminates green*1 or the entry warning light is displayed*2.


        • *1: except TFT Meter Type

        • *2: for TFT Meter Type

      4. Press the power switch with the brake pedal depressed to start the hybrid control system.

  2. CHECK PUSH-BUTTON START FUNCTION


    1. Check the push-button start function:


      1. except TFT Meter Type:

        Get into the vehicle while carrying the electrical key transmitter sub-assembly with the power switch off. With the shift lever in P, check that the entry indicator in the combination meter assembly illuminates green when the brake pedal is depressed. Then check that the hybrid control system starts when the power switch is pressed after the entry indicator in the combination meter assembly illuminates green.

      2. for TFT Meter Type:

        Get into the vehicle while carrying the electrical key transmitter sub-assembly with the power switch off. With the shift lever in P, check that the entry warning light is displayed when the brake pedal is depressed. Then check that the hybrid control system starts when the power switch is pressed after the entry warning light is displayed.

      3. While the brake pedal is released and the electrical key transmitter sub-assembly is being carried, check that the power source mode changes in the following order when the power switch is pressed: off → on (ACC) → on (IG) → off.

        Tech Tips

        When the power switch is pressed with the power switch on (IG) and the shift lever not in P, the power source mode does not change to off, but changes to on (ACC).

      4. With the shift lever in P, check that the steering lock operates when a door is opened.

        Tech Tips

        When the power switch is pressed after the vehicle is stopped, the hybrid control system stops and all the power turns off. However, if the shift lever is not in P when the power switch is pressed with the vehicle stopped, the power source mode does not change to off, but changes to on (ACC).

      5. A004FWTE03
        Text in Illustration
        *a Inspection Point

        Inspect the push start operating range (front floor). Place the electrical key transmitter sub-assembly on the front seat at either inspection point so that it is facing in the direction shown in the illustration and check that the hybrid system can be started.

        Note


        • Even if the electrical key transmitter sub-assembly is in the vehicle interior key detection area, the electrical key transmitter sub-assembly may not be properly detected if it is on the instrument panel, accessory box of the instrument panel, or in/near the front cup holder, in the glove box or on the floor.

        • Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the shift lever.

        Tech Tips

        Perform the inspection for both inspection points.

      6. A004FH6E03
        Text in Illustration
        *a Inspection Point

        Inspect the push start operating range (rear floor). Place the electrical key transmitter sub-assembly on the rear seat at either inspection point so that it is facing in the direction shown in the illustration and check that the hybrid system can be started.

        Note


        • Even if the electrical key transmitter sub-assembly is in the vehicle interior key detection area, the electrical key transmitter sub-assembly may not be properly detected if it is on the instrument panel, accessory box of the instrument panel, or in/near the front cup holder, in the glove box or on the floor.

        • Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the rear seat cushion.

        Tech Tips

        Perform the inspection for both inspection points.

  3. CHECK TRANSMITTER BATTERY SAVING FUNCTION


    1. Check the transmitter battery saving function:


      1. Press the unlock button of the electrical key transmitter sub-assembly twice while pressing the lock button and check that the electrical key transmitter sub-assembly LED blinks 4 times and enters transmitter battery saving mode.

      2. Check that the smart key system does not operate while in transmitter battery saving mode.

        Tech Tips

        To cancel transmitter battery saving mode, press a button of the electrical key transmitter sub-assembly.

  4. CHECK POWER SOURCE MODE CHANGING FUNCTION


    1. Check the power switch.


      1. Check that the power source mode changes according to the chart below.

        Shift Position Brake Pedal Power Source Mode when Power Switch Pressed
        P Released Off → on (ACC) → on (IG) → off
        P Released On (READY) → off
        P Released On (ACC)* → off
        P Depressed Off → on (READY)
        P Depressed On (ACC) → on (READY)
        P Depressed On (IG) → on (READY)
        P Depressed On (READY) → off
        P Depressed On (ACC)* → off
        Not P Released Off → on (ACC) → on (IG) (after power source mode changes to on (IG), power source mode changes between on (IG) and on (ACC) every time power switch is pressed)
        Not P Released On (READY) → on (ACC)
        Not P Depressed Off → on (IG)
        Not P Depressed On (ACC) → on (IG)
        Not P Depressed On (READY) → on (ACC)

        Tech Tips

        *: This situation is only applicable when the power source mode has changed from on (IG) READY to on (ACC) (Excludes an emergency stop by pressing the power switch 3 times quickly or pressing and holding the power switch for 2 or 3 seconds or more).

  5. CHECK POWER SOURCE MODE INDICATION


    1. A004FC2E01
      Text in Illustration
      *a Entry indicator

      Check the entry indicator. (except TFT Meter Type)

      Indicator Inspection
      Power Source Mode Indicator

      Off

      (Excluding condition in which the hybrid control system can be started)

      		 Off

      On (ACC)

      (Excluding condition in which the hybrid control system can be started)

      		 Blinking in green

      On (IG)

      (Excluding condition in which the hybrid control system can be started)

      		 Blinking in green
      Condition in which hybrid control system can be started*1 Illuminated in green
      Hybrid control system started Off
    2. A004F6FC01
      *a Power on display
      *b Entry Warning Light display

      Check the entry warning light (for TFT Meter Type).

      Multi-information Display Inspection
      Power Source Mode Multi-information Display

      Off

      (Excluding condition in which the hybrid control system can be started)

      		 Off

      On (ACC)

      (Excluding condition in which the hybrid control system can be started)

      		 "Power on" displayed

      On (IG)

      (Excluding condition in which the hybrid control system can be started)

      		 "Power on" displayed
      Condition in which hybrid control system can be started*1 Entry Warning light displayed
      Engine started Off

      Tech Tips

      *1: Indicates the condition in which the hybrid control system can be started by pressing the power switch while either of the following conditions is met:


      • Condition 1

        All of the following conditions are met:


        • The power source mode was turned from on (IG) or READY to on (ACC).

        • Key verification is OK*2 or immobiliser is unset (power switch is on (ACC) or on (IG)).

        • The shift lever is in N and the steering is unlocked.

        • The stop light switch is on.

      • Condition 2

        All of the following conditions are met:


        • The power source mode was not turned from on (IG) to on (ACC).

        • Key verification is OK*2 or immobiliser is unset (power switch is on (ACC) or on (IG)).

        • The stop light switch is on.

        • The shift lever is in P, or the shift lever is in N with the steering unlocked.

      *2: When the electrical key transmitter sub-assembly is in the vehicle, the ID code sent as a result from communication between the electrical key transmitter sub-assembly and certification ECU (smart key ECU assembly) and the ID code calculated by the certification ECU (smart key ECU assembly) are compared. If the ID codes match each other, the vehicle recognizes that the electrical key transmitter sub-assembly is in the vehicle.