ENTRY AND START SYSTEM(for Entry Function) Driver Side Door Entry Unlock Function does not Operate

DESCRIPTION

If the driver side door entry unlock function does not operate but the entry lock function operates, the communication between the vehicle and electrical key transmitter sub-assembly is normal. The malfunctioning part may be the unlock sensor circuit (from certification ECU (smart key ECU assembly) to the front door outside handle assembly (for driver side electrical key antenna)).

WIRING DIAGRAM

A004E9TE02

CAUTION / NOTICE / HINT

Note


  • When using the GTS with the vehicle power switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

  • The entry and start system (for Entry Function) uses a LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting Click here. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication system is functioning properly.

  • Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) precaution Click here.

  • Check that there are no electrical key transmitter sub-assemblies in the vehicle.

  • After repair, confirm DTC does not reoccur by performing the "DTC Output Confirmation Operation".

  • When checking the entry lock operation multiple times, the lock operation may be limited to 2 consecutive operations depending on the settings. In order to perform the entry lock operation 3 or more times, an unlock operation must be performed once (any type of unlock operation is sufficient). However, only consecutive entry lock operations are limited. Using the wireless lock or other types of lock operations, it is possible to perform consecutive lock operations without this limitation.

PROCEDURE


  1. CHECK POWER DOOR LOCK OPERATION


    1. When the door control switch on the master switch assembly is operated, check that the doors unlock and lock according to switch operation Click here.

      OK
      Door locks operate normally.

    NG

    GO TO POWER DOOR LOCK CONTROL SYSTEM (PROCEED TO PROBLEM SYMPTOMS TABLE) Click here

    OK

  2. READ VALUE USING GTS (UNLOCK DETECTION SWITCH)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Data List.

    5. According to the display on the GTS, read the Data List.

      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      FR Door Lock Pos*2 Front door unlock detection switch RH signal / LOCK or UNLOCK

      LOCK: Front RH side door locked

      UNLOCK: Front RH side door unlocked

      		 -
      FL Door Lock Pos*1 Front door unlock detection switch LH signal / LOCK or UNLOCK

      LOCK: Front LH side door locked

      UNLOCK: Front LH side door unlocked

      		 -

      • *1: for LHD

      • *2: for RHD

      OK
      On the GTS screen, the display changes between ON and OFF as shown in the table above.

    NG

    GO TO LIGHTING SYSTEM (PROCEED TO DOOR UNLOCK DETECTION SWITCH CIRCUIT) Click here

    OK

  3. READ VALUE USING GTS (D-DOOR TOUCH SENSOR)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Entry & Start / Data List.

    5. According to the display on the GTS, read the Data List.

      Entry & Start
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      D-Door Touch Sensor Front door outside handle assembly (for driver side) (lock sensor) / OFF or ON

      OFF: Front door outside handle assembly (for driver side) (unlock sensor) not touched

      ON: Front door outside handle assembly (for driver side) (unlock sensor) touched

      • Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

      • Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.
      OK
      On the GTS screen, the display changes between ON and OFF as shown in the table above.

    OK

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    NG

  4. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER SIDE DOOR))


    1. Disconnect the F86 and F88 certification ECU (smart key ECU assembly) connectors.

    2. Disconnect the H9*1 or G9*2 front door outside handle assembly (for driver side door) connector.


      • *1: for LHD

      • *2: for RHD

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      F86-22 (SEN1) - H9-4 (SENS) Always Below 1 Ω
      F88-11 (E) - Body ground Always Below 1 Ω
      F86-22 (SEN1) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      F86-22 (SEN1) - G9-4 (SENS) Always Below 1 Ω
      F88-11 (E) - Body ground Always Below 1 Ω
      F86-22 (SEN1) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. INSPECT FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER SIDE DOOR)


    1. Reconnect the F86 and F88 certification ECU (smart key ECU assembly) connectors.

    2. Reconnect the H9*1 or G9*2 front door outside handle assembly (for driver side door) connector.


      • *1: for LHD

      • *2: for RHD

    3. Using an oscilloscope, check the waveform.

      A004G7IE01
      Text in Illustration
      *a

      Component with harness connected

      (Certification ECU (smart key ECU assembly))

      		 *b Waveform
      *c In actuality, sampling is being performed - -
      OK
      Tester Connection Switch Condition Tool Setting Specified Condition
      F86-22 (SEN1) - F88-11 (E)

      Procedure:


      1. Power switch off

      2. Electrical key transmitter sub-assembly brought outside vehicle

      3. All doors locked

      4. Electrical key transmitter sub-assembly not sufficiently close to vehicle

      5. Driver side door unlock sensor not touched → touched

      		 2 V/DIV., 500 ms./DIV.

      Pulse generation

      (See waveform)

    OK

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    NG

    REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FRONT DRIVER SIDE DOOR) Click here