CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense) TERMINALS OF ECU

Note


  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

  • Turn the ignition switch off before measuring the resistances between CAN main bus lines and between CAN branch lines.

  • Turn the ignition switch off before inspecting CAN bus lines for a ground short.

  • Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

  • This section describes the standard values for all CAN related components.

Tech Tips


  • Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

  • Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.


  1. CAN JUNCTION CONNECTOR LH

    Tech Tips

    The following tables contain information about the items and buses connected via junction connectors. The junction connector may be used for multiple separate buses. In this case, the name of the bus will be shown below the name of the item that the terminals are connected to. The bus name will be shown in brackets (example: (for Sub bus 15)).


    1. Check the CAN junction connector LH (instrument panel wire side) (for bus 2).


      1. Connection diagram

        A01UY5ZE02
        Text in Illustration
        *a

        Front view of wire harness connector

        (to CAN Junction Connector LH (Instrument Panel Wire Side))

        		 *b

        to Main Body ECU (Multiplex Network Body ECU)

        (for Bus 2)
        *c

        to CAN Junction Connector RH

        (for Bus 2)

        		 *d

        to Hybrid Vehicle Control ECU

        (for Bus 2)
        *e

        Pre-crash Safety City Sensor

        (for Bus 2)

        		 - -

      2. Check the connection diagram of the components which are connected to the CAN junction connector LH.

        Terminal No. (Symbol) Wiring Color Connected to
        F90-1 (CANH) R

        Main body ECU (Multiplex network body ECU)

        (for bus 2)
        F90-12 (CANL) W
        F90-2 (CANH) R

        Pre-crash Safety City Sensor

        (for bus 2)
        F90-13 (CANL) W
        F90-3 (CANH) BE

        Hybrid vehicle control ECU

        (for bus 2)
        F90-14 (CANL) W
        F90-4 (CANH) SB

        CAN junction connector RH

        (for bus 2)
        F90-15 (CANL) W

    2. Check the CAN junction connector LH (engine room main wire side) (for bus 2).


      1. Connection diagram

        A01V1YEE03
        Text in Illustration
        *a

        Front view of wire harness connector

        (to CAN Junction Connector LH (Engine Room Main Wire Side))

        		 *b

        to ECM

        (for Bus 2)
        *c

        to Brake Booster with Master Cylinder Assembly (Skid Control ECU)

        (for Bus 2)

        		 - -

      2. Check the connection diagram of the components which are connected to the CAN junction connector LH.

        Terminal No. (Symbol) Wiring Color Connected to
        A52-9 (CANH) L

        ECM

        (for bus 2)
        A52-20 (CANL) W
        A52-10 (CANH) B

        Brake booster with master cylinder assembly (Skid control ECU)

        (for bus 2)
        A52-21 (CANL) W

  2. CAN JUNCTION CONNECTOR RH


    1. Check the CAN junction connector RH (for bus 2).


      1. Connection diagram

        A01V1SZE02
        Text in Illustration
        *a

        Front view of wire harness connector

        (to CAN Junction Connector RH)

        		 *b

        to Spiral Cable with Sensor Sub-assembly (Steering Sensor)

        (for Bus 2)
        *c

        to Smart Key ECU Assembly (Certification ECU)*1

        (for Bus 2)

        		 *d

        to Airbag Sensor Assembly

        (for Bus 2)
        *e

        to Power Steering ECU Assembly

        (for Bus 2)

        		 *f

        to Combination Meter Assembly

        (for Bus 2)
        *g

        to Air Conditioning Amplifier Assembly

        (for Bus 2)

        		 *h

        to CAN Junction Connector LH

        (for Bus 2)
        *i

        to Central Gateway ECU (Network Gateway ECU)

        (for Bus 2)

        		 - -

        • *1: w/ Power Switch

      2. Check the connection diagram of the components which are connected to the CAN junction connector RH.

        Terminal No. (Symbol) Wiring Color Connected to
        F63-1 (CANH) P

        Spiral cable with sensor sub-assembly (Steering sensor)

        (for bus 2)
        F63-12 (CANL) W
        F63-2 (CANH) L

        Central gateway ECU (network gateway ECU)

        (for bus 2)
        F63-13 (CANL) W
        F63-3 (CANH) L

        Smart key ECU assembly (Certification ECU)*1

        (for bus 2)
        F63-14 (CANL) W
        F63-4 (CANH) B

        Airbag sensor assembly

        (for bus 2)
        F63-15 (CANL) W
        F63-6 (CANH) LG

        Power Steering ECU Assembly

        (for bus 2)
        F63-17 (CANL) W
        F63-7 (CANH) G

        Combination meter assembly

        (for bus 2)
        F63-18 (CANL) W
        F63-8 (CANH) V

        Air conditioning amplifier assembly

        (for bus 2)
        F63-19 (CANL) W
        F63-10 (CANH) SB

        CAN junction connector LH

        (for bus 2)
        F63-21 (CANL) W

        • *1: w/ Power Switch

  3. CAN JUNCTION CONNECTOR LH


    1. Check the CAN junction connector LH (instrument panel wire side) (for bus 3).


      1. Connection diagram

        A01UXJ0E02
        Text in Illustration
        *a

        Front view of wire harness connector

        (to CAN Junction Connector LH (Instrument Panel Wire Side))

        		 *b

        to Central Gateway ECU (Network Gateway ECU) (CA3H and CA3L Terminal)

        (for Bus 3)
        *c

        to Central Gateway ECU (Network Gateway ECU) (CAYH and CAYL Terminal)

        (for Bus 3)

        		 *d

        to Radio and Display Receiver Assembly*1

        (for Bus 3)

        • *1: w/ Display

      2. Check the connection diagram of the components which are connected to the CAN junction connector LH.

        Terminal No. (Symbol) Wiring Color Connected to
        F90-5 (CANH) BE

        Radio and display receiver assembly*1

        (for Bus 3)
        F90-16 (CANL) W
        F90-6 (CANH) R

        Central gateway ECU (network gateway ECU) (CAYH and CAYL terminal)

        (for Bus 3)
        F90-17 (CANL) W
        F90-7 (CANH) G

        Central gateway ECU (network gateway ECU) (CA3H and CA3L terminal)

        (for Bus 3)
        F90-18 (CANL) W

        • *1: w/ Display

  4. CAN JUNCTION CONNECTOR LH


    1. Check the CAN junction connector LH (engine room main wire side) (for Sub bus 15).


      1. Connection diagram

        A01UZNTE02
        Text in Illustration
        *a

        Front view of wire harness connector

        (to CAN Junction Connector LH (Engine Room Main Wire Side))

        		 *b

        to Brake Booster with Master Cylinder Assembly (Skid Control ECU)

        (for Sub Bus 15)
        *c

        to ECM

        (for Sub Bus 15)

        		 - -

      2. Check the connection diagram of the components which are connected to the CAN junction connector LH.

        Terminal No. (Symbol) Wiring Color Connected to
        A52-1 (CANH) L

        Brake booster with master cylinder assembly (Skid control ECU)

        (for Sub bus 15)
        A52-12 (CANL) W
        A52-3 (CANH) B*1, G*2

        ECM

        (for Sub bus 15)
        A52-14 (CANL) W

        • *1: for LHD

        • *2: for RHD

    2. Check the CAN junction connector LH (instrument panel wire side) (for Sub bus 15).


      1. Connection diagram

        A01UZWDE02
        Text in Illustration
        *a

        Front view of wire harness connector

        (to CAN Junction Connector LH (Instrument Panel Wire Side))

        		 *b

        to Hybrid Vehicle Control ECU

        (for Sub Bus 15)

      2. Check the connection diagram of the components which are connected to the CAN junction connector LH.

        Terminal No. (Symbol) Wiring Color Connected to
        F90-10 (CANH) Y

        Hybrid vehicle control ECU

        (for Sub bus 15)
        F90-21 (CANL) W

  5. DLC3


    1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    2. A01UZFIE01
      Text in Illustration
      *1 DLC3

      Measure the resistance according to the value(s) in the table below.

    3. CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

      A01V0JCE02
      4. Text in Illustration
      *a

      Component without harness connected

      (Central Gateway ECU (Network Gateway ECU))

      		 - -

      1. Disconnect the cable from the negative (-) auxiliary battery terminal.

      2. A01V0JTE01
        Text in Illustration
        *a

        Front view of wire harness connector

        (to Central Gateway ECU (Network Gateway ECU))

        Disconnect the central gateway ECU (network gateway ECU) connector.

      3. Measure the resistance according to the value(s) in the table below.

      4. A01UZVXE02
        5. Text in Illustration
        *a

        Rear view of wire harness connector

        (to Central Gateway ECU (Network Gateway ECU))

Reconnect the central gateway ECU (network gateway ECU) connector.

  • Measure the resistance according to the value(s) in the table below.

  • HYBRID VEHICLE CONTROL ECU

    A01V1L2E02
    • Text in Illustration
    *a

    Component without harness connected

    (Hybrid Vehicle Control ECU)

    		 - -

    1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    2. A01V16GE01
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Hybrid Vehicle Control ECU)

      Disconnect the hybrid vehicle control ECU connectors.

    3. Measure the resistance according to the value(s) in the table below.

    4. ECM

      A01UXGWE02
      5. Text in Illustration
      *A for LHD *B for RHD
      *a

      Component without harness connected

      (ECM)

      		 - -

      1. Disconnect the cable from the negative (-) auxiliary battery terminal.

      2. Disconnect the ECM connectors.

        A01V19SE01
        Text in Illustration
        *A for LHD *B for RHD
        *a

        Front view of wire harness connector

        (to ECM)

        		 - -

      3. Measure the resistance according to the value(s) in the table below.

        *1: for LHD

        *2: for RHD

        *1: for LHD

        *2: for RHD

      4. BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU)

        A01UYYVE01
        5. Text in Illustration
        *a

        Component without harness connected

        (Brake Booster with Master Cylinder Assembly (Skid Control ECU))

        		 - -

        1. Disconnect the cable from the negative (-) auxiliary battery terminal.

        2. A01V1WHE01
          Text in Illustration
          *a

          Front view of wire harness connector

          (to Brake Booster with Master Cylinder Assembly (Skid Control ECU))

          Disconnect the brake booster with master cylinder assembly (skid control ECU) connector.

        3. Measure the resistance according to the value(s) in the table below.

        4. AIRBAG SENSOR ASSEMBLY

          A01V23QE01
          5. Text in Illustration
          *a

          Component without harness connected

          (Airbag Sensor Assembly)

          		 - -

          1. Disconnect the cable from the negative (-) auxiliary battery terminal.

          2. Disconnect the airbag sensor assembly connector.

            A01V1KSE01
            Text in Illustration
            *1 DLC3 - -
            *a

            Front view of wire harness connector

            (to Airbag Sensor Assembly)

            		 - -

          3. Measure the resistance according to the value(s) in the table below.

          4. MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

            A01V13ZE02
            5. Text in Illustration
            *1 Main Body ECU (Multiplex Network Body ECU) - -
            *a

            Component without harness connected

            (Main body ECU (Multiplex Network Body ECU))

            		 - -

            1. Disconnect the cable from the negative (-) auxiliary battery terminal.

            2. Disconnect the main body ECU (multiplex network body ECU) connector.

              A01UZGQE01
              Text in Illustration
              *1 DLC3 - -
              *a

              Front view of wire harness connector

              (to Main Body ECU (Multiplex Network Body ECU))

              		 - -

            3. Measure the resistance according to the value(s) in the table below.

            4. SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY (STEERING SENSOR)


              1. Disconnect the cable from the negative (-) auxiliary battery terminal.

              2. A01UXM2E01
              5. Text in Illustration
              *a

              Front view of wire harness connector

              (to Spiral Cable with Sensor Sub-assembly (Steering Sensor))

              Disconnect the spiral cable with sensor sub-assembly (steering sensor) connector.

            5. Measure the resistance according to the value(s) in the table below.

            6. POWER STEERING ECU ASSEMBLY

              A01V0BGE01
              7. Text in Illustration
              *a

              Component without harness connected

              (Power Steering ECU Assembly)

              		 - -

              1. Disconnect the cable from the negative (-) auxiliary battery terminal.

              2. Disconnect the power steering ECU assembly connectors.

                A01V1WGE02
                Text in Illustration
                *a

                Front view of wire harness connector

                (to Power Steering ECU Assembly)

                		 - -

              3. Measure the resistance according to the value(s) in the table below.

              4. SMART KEY ECU ASSEMBLY (CERTIFICATION ECU) (w/ Power Switch)

                A01V01PE01
                5. Text in Illustration
                *a

                Component without harness connected

                (Smart Key ECU Assembly (Certification ECU))

                		 - -

                1. Disconnect the cable from the negative (-) auxiliary battery terminal.

                2. A01V11AE02
                  Text in Illustration
                  *a

                  Front view of wire harness connector

                  (to Smart Key ECU Assembly (Certification ECU))

                  Disconnect the smart key ECU assembly (certification ECU) connectors.

                3. Measure the resistance according to the value(s) in the table below.

                4. COMBINATION METER ASSEMBLY

                  A01UXY8E01
                  5. Text in Illustration
                  *a

                  Component without harness connected

                  (Combination Meter Assembly)

                  		 - -

                  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

                  2. A01UZFJE01
                    Text in Illustration
                    *a

                    Front view of wire harness connector

                    (to Combination Meter Assembly)

                    Disconnect the combination meter assembly connector.

                  3. Measure the resistance according to the value(s) in the table below.

                  4. AIR CONDITIONING AMPLIFIER ASSEMBLY

                    A01V1DQE02
                    5. Text in Illustration
                    *a

                    Component without harness connected

                    (Air Conditioning Amplifier Assembly)

                    		 - -

                    1. Disconnect the cable from the negative (-) auxiliary battery terminal.

                    2. A01V0GDE02
                      Text in Illustration
                      *a

                      Front view of wire harness connector

                      (to Air Conditioning Amplifier Assembly)

                      Disconnect the air conditioning amplifier assembly connector.

                    3. Measure the resistance according to the value(s) in the table below.

                    4. RADIO AND DISPLAY RECEIVER ASSEMBLY (w/ Display)

                      A01V11EE02
                      5. Text in Illustration
                      *a

                      Component without harness connected

                      (Radio and Display Receiver Assembly)

                      		 - -

                      1. Disconnect the cable from the negative (-) auxiliary battery terminal.

                      2. A01V1L4E01
                        Text in Illustration
                        *a

                        Front view of wire harness connector

                        (to Radio and Display Receiver Assembly)

                        Disconnect the radio and display receiver assembly connectors.

                      3. Measure the resistance according to the value(s) in the table below.

                      4. PRE-CRASH SAFETY CITY SENSOR

                        A01V0F9E01
                        5. Text in Illustration
                        *a

                        Component without harness connected

                        (Pre-crash Safety City Sensor)

                        		 - -

                        1. Disconnect the cable from the negative (-) auxiliary battery terminal.

                        2. A01V1T3E01
                          Text in Illustration
                          *1 DLC3
                          *a

                          Front view of wire harness connector

                          (to Pre-crash Safety City Sensor)

                          Disconnect the pre-crash safety city sensor connector.

                        3. Measure the resistance according to the value(s) in the table below.