ELECTRONICALLY CONTROLLED BRAKE SYSTEM, Diagnostic DTC:C1249/49

DTC Code DTC Name
C1249/49 Open in Stop Light Switch Circuit

DESCRIPTION

The skid control ECU receives the stop light switch assembly signal and detects the brake pedal operation status.

The skid control ECU has an open detection circuit, which stores this DTC if it detects an open in the stop light input line or ground line of the stop light circuit with the stop light switch assembly off (brake pedal not depressed).

DTC No. INF Code DTC Detection Condition Trouble Area
C1249/49 231 When IG1 terminal voltage is 9.5 V or more, an open stop light switch circuit continues for 10 seconds or more.

  • Wire harness or connector

  • Stop light switch assembly

  • Skid control ECU (Brake booster with master cylinder assembly)

WIRING DIAGRAM

A01UZBVE02

CAUTION / NOTICE / HINT

Note


  • When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve Click here.

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. CHECK STOP LIGHT OPERATION


    1. Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

      OK
      Stop lights come on when brake pedal depressed, and go off when brake pedal released.

    NG

    INSPECT STOP LIGHT SWITCH ASSEMBLY Click here

    OK

  2. READ VALUE USING GTS (STOP LIGHT SW)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    5. According to the display on the GTS, read the Data List.

      ABS/VSC/TRC
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Stop Light SW Stop light switch assembly / ON or OFF

      ON: Brake pedal depressed

      OFF: Brake pedal released

      		 -

    6. Check that the stop light switch assembly display observed on the GTS changes according to brake pedal operation.

      OK
      The GTS displays ON or OFF according to brake pedal operation.

    NG

    CHECK HARNESS AND CONNECTOR (STP TERMINAL) Click here

    OK

  3. RECONFIRM DTC


    1. Turn the ignition switch off.

    2. Clear the DTCs Click here.

    3. Turn the ignition switch to ON (READY).

    4. Depress the brake pedal several times to test the stop light circuit.

    5. Check if the same DTC is output Click here.

      Result
      Result Proceed to
      DTC C1249/49 is not output. A
      DTC C1249/49 is output (for LHD). B
      DTC C1249/49 is output (for RHD). C

      Tech Tips

      If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step Click here.


    A

    CHECK FOR INTERMITTENT PROBLEMS Click here

    B

    REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY Click here

    C

    REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY Click here

  4. INSPECT STOP LIGHT SWITCH ASSEMBLY


    1. Check the stop light switch assembly.


      • for LED Type Stop Light (See page)

      • for Bulb Type Stop Light (See page)

      OK
      The stop light switch assembly is normal.

    NG

    REPLACE STOP LIGHT SWITCH ASSEMBLY Click here

    OK

  5. CHECK HARNESS AND CONNECTOR (STP TERMINAL)


    1. A01V1MCE02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Skid Control ECU (Brake Booster with Master Cylinder Assembly))

      Make sure that there is no looseness at the locking part and the connecting part of the connector.

    2. Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      A29-33 (STP) - Body ground Stop light switch assembly ON (Brake pedal depressed) 11 to 14 V
      A29-33 (STP) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

    OK

  6. RECONFIRM DTC


    1. Reconnect the skid control ECU (brake booster with master cylinder assembly) connector.

    2. Clear the DTCs Click here.

    3. Turn the ignition switch to ON (READY).

    4. Depress the brake pedal several times to test the stop light circuit.

    5. Check if the same DTC is output Click here.

      Result
      Result Proceed to
      DTC C1249/49 is not output. A
      DTC C1249/49 is output. B

      Tech Tips


      • If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step Click here.

      • If the lighting system is normal but the DTC is still output, replace the skid control ECU (brake booster with master cylinder assembly) (See page for LHD or Click here for RHD).


    A

    CHECK FOR INTERMITTENT PROBLEMS Click here

    B

    INSPECT LIGHTING SYSTEM (PROBLEM SYMPTOMS TABLE) Click here

  7. CHECK HARNESS AND CONNECTOR (STP TERMINAL)


    1. A01V1MCE02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Skid Control ECU (Brake Booster with Master Cylinder Assembly))

      Turn the ignition switch off.

    2. Make sure that there is no looseness at the locking part and the connecting part of the connector.

    3. Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      A29-33 (STP) - Body ground Stop light switch assembly ON (Brake pedal depressed) 11 to 14 V
      A29-33 (STP) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V
      Result
      Result Proceed to
      OK (for LHD) A
      OK (for RHD) B
      NG C

      Tech Tips

      If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step Click here.


    A

    REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY Click here

    B

    REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY Click here

    C

    REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)