TIRE PRESSURE WARNING SYSTEM, Diagnostic DTC:C2177/77

DTC Code DTC Name
C2177/77 Initialization not Completed

DESCRIPTION

Initialization is necessary if one of the following occurs:


DTC No. DTC Detection Condition Trouble Area
C2177/77

  • All conditions below are met:


  • During initialization

  • Tire pressure warning valve and transmitter is not in stop mode

  • Signal is not received from tire pressure warning valve and transmitter for 10 minutes or more

  • Vehicle speed is more than 37 km/h (23 mph) for a total of 10 minutes

  • Tire pressure warning valve and transmitter

  • Wire harness or connector

  • Tire pressure warning ECU and receiver

WIRING DIAGRAM

A01V16EE17

CAUTION / NOTICE / HINT

Note


  • When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

  • It is necessary to perform initialization (See page ) after registration Click here of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU and/or one of the valve and transmitters has been replaced.

PROCEDURE


  1. CHECK FREQUENCY RECEIVING CONDITION


    1. Check that the vehicle is not located in an area such as described below:


      1. Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.

        Tech Tips

        If the vehicle is located in an area such as the one described above, the tire pressure warning light may come on after blinking 1 minute only in a particular area due to interfering radio frequencies.

      2. Devices using similar radio frequencies are used in the vehicle.

        OK
        Facilities, or devices that use similar radio frequencies are not located in the vicinity of the vehicle.

        Tech Tips

        Radio transmissions may be interrupted due to the surroundings, or devices installed by the user.


    NG

    CHECK IF ANY DEVICE IS INSTALLED BY USER

    OK

  2. PERFORM INITIALIZATION


    1. Perform initialization Click here.


    NEXT

  3. CONFIRM TIRE INFLATION PRESSURE (DATA LIST)


    1. Turn the ignition switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the ignition switch to ON (IG).

    4. Turn the GTS on.

    5. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

    6. Check the values by referring to the table below.

      Tire Pressure Monitor
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      ID1 Tire Inflation Pressure

      ID1 tire inflation pressure/

      min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)

      max.: Absolute pressure (abs) / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 388.72 kPa (3.9 kgf/cm2, 56 psi)

      		 Actual tire inflation pressure If N/A is displayed, data has not been received.*
      ID2 Tire Inflation Pressure

      ID2 tire inflation pressure /

      min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)

      max.: Absolute pressure (abs) / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 388.72 kPa (3.9 kgf/cm2, 56 psi)

      		 Actual tire inflation pressure If N/A is displayed, data has not been received.*
      ID3 Tire Inflation Pressure

      ID3 tire inflation pressure /

      min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)

      max.: Absolute pressure (abs) / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 388.72 kPa (3.9 kgf/cm2, 56 psi)

      		 Actual tire inflation pressure If N/A is displayed, data has not been received.*
      ID4 Tire Inflation Pressure

      ID4 tire inflation pressure /

      min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)

      max.: Absolute pressure (abs) / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 388.72 kPa (3.9 kgf/cm2, 56 psi)

      		 Actual tire inflation pressure If N/A is displayed, data has not been received.*

      Tech Tips


      • *: It may take a few minutes until the values are displayed.

      • When no "ID Tire Inflation Pressure" data has changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the data.

      Result
      Result Proceed to
      Tire pressure values are not displayed. A
      All tire pressure readings are equal to specified values. B

    A

    GO TO DTC C2121/21 TO C2124/24 Click here

    B

    END