REAR AXLE HUB BOLT REPLACEMENT

CAUTION / NOTICE / HINT

Note


  • When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be output. As there is no malfunction, clear the DTC.

  • While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or the door courtesy switch is turned on. Therefore, even if only brake pads are to be removed and installed, be sure to perform the Disable Brake Control procedure and disconnect the cable from the negative (-) terminal of the auxiliary battery before beginning work.

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work Click here.

  2. DISABLE BRAKE CONTROL

    Click here

  3. REMOVE REAR WHEEL

  4. SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY

    Click here

  5. SEPARATE REAR DISC BRAKE CYLINDER ASSEMBLY


    1. A01UXQC

      Remove the 2 bolts and separate the rear disc brake cylinder assembly from the rear axle beam assembly.

      Note

      Hang the rear disc brake cylinder assembly using a piece of string or the equivalent.

  6. REMOVE REAR DISC

    Click here

  7. REMOVE REAR AXLE HUB BOLT


    1. A01UZ5AE02
      Text in Illustration
      *1 Service Nut
      *a Turn
      *b Hold

      Temporarily install 2 service nuts to the 2 rear axle hub bolts as shown in the illustration.

      Recommended Service Nut
      Thread Diameter Thread Pitch
      12.0 mm (0.472 in.) 1.5 mm (0.0591 in.)

      Note

      Install the service nuts to prevent damage to the rear axle hub bolts.

    2. Using SST and a screwdriver or the equivalent to hold the rear axle hub and bearing assembly, remove the rear axle hub bolt.

      SST
      09628-10011

      Note

      Do not damage the threads of the rear axle hub bolts.

  8. INSTALL REAR AXLE HUB BOLT


    1. Temporarily install a new rear axle hub bolt to the rear axle hub and bearing assembly.

    2. A01UYFJE02
      Text in Illustration
      *1 Washer
      *2 Service Nut
      *a Turn
      *b Hold

      Install a washer and service nut to the rear axle hub bolt as shown in the illustration.

      Recommended Service Nut
      Thread Diameter Thread Pitch
      12.0 mm (0.472 in.) 1.5 mm (0.0591 in.)

      Tech Tips

      Recommended thickness of the washer is 5 mm (0.197 in.) or more.

    3. Using a screwdriver or the equivalent to hold the rear axle hub and bearing assembly, install the rear axle hub bolt by tightening the service nut.

      Note


      • Install the service nuts to prevent damage to the rear axle hub bolts.

      • Do not damage the threads of the rear axle hub bolts.

    4. Remove the 3 service nuts and washer from the 3 rear axle hub bolts.

  9. INSTALL REAR DISC

    Click here

  10. INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY


    1. Install the rear disc brake cylinder assembly to the rear axle beam assembly with the 2 bolts.

      Torque:
      57 N*m  { 585 kgf*cm, 42 ft.*lbf }

  11. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY

    Click here

  12. INSTALL REAR WHEEL

    Torque:
    103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

  13. INSPECT AND ADJUST PARKING BRAKE LEVER TRAVEL

    Click here

  14. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Click here