HYBRID CONTROL SYSTEM, Diagnostic DTC:P0D2E-586

DTC Code DTC Name
P0D2E-586 Drive Motor "A" Inverter Voltage Sensor Circuit Range / Performance

DESCRIPTION

For a description of the inverter Click here.

The signal line from the inverter voltage (VH) sensor is connected to the MG ECU inside the inverter with converter assembly.

Tech Tips

The term "drive motor A" indicates MG2.

DTC No. INF Code DTC Detection Condition Trouble Area
P0D2E 586

Inverter voltage (VH) sensor performance problem

During inverter voltage does not boosted difference between "VH-Voltage after Boosting" and "VL-Voltage before Boosting" is large and difference between "VH-Voltage after Boosting" and "Power Resource VB" is large.

(1 trip detection logic)

 Inverter with converter assembly
Related Data List
DTC No. Data List
P0D2E-586

  • VL-Voltage before Boos

  • VH-Voltage after Boosting

  • Power Resource VB

CAUTION / NOTICE / HINT

Tech Tips

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.


  1. Turn the ignition switch to ON (READY) with the shift lever in P.

  2. Confirm that the Data List item "Boost Ratio" is 0 % when the accelerator pedal is not depressed. Check that the Data List items "VH-Voltage after Boosting" and "Power Resource VB" are almost the same.

PROCEDURE


  1. CHECK DTC OUTPUT (HYBRID CONTROL)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Check if DTCs are output.

      Result
      Result Proceed to
      Only P0D2E-586 is output or P0D2E-586 and DTCs other than the ones in the table below are also output. A
      DTCs shown in Table 1 are output simultaneously. B
      DTCs shown in Table 2 are output simultaneously. C
      Table 1
      DTC No. Relevant Diagnosis
      P06E6-164 Sensor Power Supply "C" Circuit/Open
      P0A1A-151, 658 Generator Control Module
      P0A1B-786 Drive Motor "A" Control Module
      P0A1D-148 Hybrid Powertrain Control Module
      P0D2F-266 Drive Motor "A" Inverter Voltage Sensor Circuit Low
      P0D30-267 Drive Motor "A" Inverter Performance
      P0E33-589 DC/DC Converter Voltage Sensor "A" Low
      P0E34-590 DC/DC Converter Voltage Sensor "A" High
      P1C2A-155 Generator A/D Converter Circuit
      P1C73-512 Sensor Standard Voltage "F" Circuit/Open
      P1CA6-156 Generator Control Module Malfunction
      P1CA7-193 Drive Motor Control Module Malfunction
      P2511-149 HV CPU Power Relay Sense Circuit Intermittent No Continuity
      P3133-659 Communication Error from Generator to Drive Motor "A"
      P3134-661 Communication Error from Drive Motor "A" to Generator
      P324E-788 MG-ECU Power Relay Intermittent Circuit
      U0110 (all INF codes)*1 Lost Communication with Drive Motor Control Module "A"
      Table 2
      DTC No. Relevant Diagnosis
      P0AFC-123 Hybrid Battery Pack Sensor Module
      P0B3D-123 Hybrid Battery Voltage Sensor "A" Circuit Low
      P0B42-123 Hybrid Battery Voltage Sensor "B" Circuit Low
      P0B47-123 Hybrid Battery Voltage Sensor "C" Circuit Low
      P0B4C-123 Hybrid Battery Voltage Sensor "D" Circuit Low
      P0B51-123 Hybrid Battery Voltage Sensor "E" Circuit Low
      P0B56-123 Hybrid Battery Voltage Sensor "F" Circuit Low
      P0B5B-123 Hybrid Battery Voltage Sensor "G" Circuit Low
      P0B60-123 Hybrid Battery Voltage Sensor "H" Circuit Low
      P0B65-123 Hybrid Battery Voltage Sensor "I" Circuit Low
      P0B6A-123 Hybrid Battery Voltage Sensor "J" Circuit Low
      P0B6F-123 Hybrid Battery Voltage Sensor "K" Circuit Low
      P308A-123 Hybrid Battery Voltage Sensor All Circuits Low

      Tech Tips


      • *1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.

      • P0D2E-586 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.

    5. Turn the ignition switch off.


    A

    REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS Click here

    B

    GO TO DTC CHART (HYBRID CONTROL SYSTEM) Click here

    C

    GO TO DTC CHART (HYBRID BATTERY SYSTEM) Click here