HYBRID CONTROL SYSTEM, Diagnostic DTC:P0AFC-150

DTC Code DTC Name
P0AFC-150 Hybrid Battery Pack Sensor Module

DESCRIPTION

The power management control ECU alerts the driver and performs fail-safe control based on error signals sent from the battery smart unit.

DTC NO. INF Code DTC Detection Condition Trouble Area
P0AFC 150 Power source voltage of the battery smart unit drops during precharge.

  • Battery smart unit

  • Wire harness or connector

WIRING DIAGRAM

A01UZWQE02

CAUTION / NOTICE / HINT

CAUTION:


  • Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, turn the ignition switch off and take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

  • After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work Click here.

    Tech Tips

    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

Note

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

Tech Tips


  • After completing repairs, restart the system (turn the ignition switch to ON (READY)) and recheck for DTCs Click here.

  • After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.


    1. Turn the ignition switch to ON (READY) and wait for 15 seconds or more.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (IGCT VOLTAGE)

    CAUTION:

    Be sure to wear insulated gloves.


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Remove the No. 1 hybrid battery exhaust duct Click here.

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Turn the ignition switch to ON (IG).

    5. A01UZ9TE02
      Text in Illustration
      *a

      Component with harness connected

      (Battery Smart Unit)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      K32-3 (IGCT) - K32-6 (GND) Ignition switch ON (IG) 11 to 14 V

      Note

      Turning the ignition switch to ON (IG) with the service grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

    6. Turn the ignition switch off.

    7. Disconnect the cable from the negative (-) auxiliary battery terminal.

    8. Install the No. 1 hybrid battery exhaust duct.


    OK

    REPLACE BATTERY SMART UNIT Click here

    NG

  2. CHECK HARNESS AND CONNECTOR (BATTERY SMART UNIT - BODY GROUND)

    CAUTION:

    Be sure to wear insulated gloves.


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Remove the No. 1 hybrid battery exhaust duct Click here.

    3. A01UZGFE02
      Text in Illustration
      *a

      Component with harness connected

      (Battery Smart Unit)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      K32-6 (GND) - Body ground Ignition switch off Below 1 Ω

    4. Install the No. 1 hybrid battery exhaust duct.


    OK

    REPAIR OR REPLACE HARNESS OR CONNECTOR (IGCT NO. 4 FUSE - BATTERY SMART UNIT)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY SMART UNIT - BODY GROUND)