NAME PLATE INSTALLATION

PROCEDURE


  1. INSTALL SIDE PANEL EMBLEM


    1. Clean the attachment surface.


      1. Using an infrared light, heat the double-sided tape remaining on the front fender panel.

        Heating Temperature
        Item Temperature
        Vehicle Body 40 to 60°C (104 to 140°F)

        CAUTION:

        Do not burn yourself on the hot body panel or with the infrared light.

        Note

        Do not heat the front fender panel excessively.

      2. Using a piece of cloth, rub the double-sided tape off the front fender panel while it is hot from the infrared light.

        Note

        Installing the side panel emblem while any double-sided tape remains on the front fender panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

      3. Using a non-residue solvent, clean the attachment surface.

    2. Install a new side panel emblem as shown in the illustration.

      A004FU4C01
      *a LH side *b RH side
      Installation Position
      Mark Measurement Mark Measurement
      A 125.1 mm (4.92 in.) B 112.7 mm (4.43 in.)
      C 202.3 mm (7.96 in.) D 54.0 mm (2.12 in.)
      E 113.0 mm (4.45 in.) F 123.9 mm (4.88 in.)
      G 196.1 mm (7.72 in.) H 48.4 mm (1.91 in.)

      Note

      Install the side panel emblem in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the front fender panel and the side panel emblem to 20 to 30°C (68 to 86°F) and install the side panel emblem.

  2. INSTALL SYMBOL EMBLEM

    Click here

  3. INSTALL NO. 6 BACK DOOR NAME PLATE


    1. Clean the attachment surface.


      1. Using an infrared light, heat the double-sided tape remaining on the back door panel.

        Heating Temperature
        Item Temperature
        Vehicle Body 40 to 60°C (104 to 140°F)

        CAUTION:

        Do not burn yourself on the hot body panel or with the infrared light.

        Note

        Do not heat the back door panel excessively.

      2. Using a piece of cloth, rub the double-sided tape off the back door panel while it is hot from the infrared light.

        Note

        Installing the No. 6 back door name plate while any double-sided tape remains on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

      3. Using a non-residue solvent, clean the attachment surface.

    2. Install a new No. 6 back door name plate as shown in the illustration.

      A004FENN01
      Installation Position
      Area Measurement Area Measurement
      A 72.8 mm (2.87 in.) B 54.6 mm (2.15 in.)
      C 40.9 mm (1.61 in.) D 186.4 mm (7.34 in.)

      Note

      Install the No. 6 back door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 6 back door name plate to 20 to 30°C (68 to 86°F) and install the No. 6 back door name plate.

  4. INSTALL NO. 2 LUGGAGE COMPARTMENT DOOR NAME PLATE


    1. Clean the attachment surface.


      1. Using an infrared light, heat the double-sided tape remaining on the back door panel.

        Heating Temperature
        Item Temperature
        Vehicle Body 40 to 60°C (104 to 140°F)

        CAUTION:

        Do not burn yourself on the hot body panel or with the infrared light.

        Note

        Do not heat the back door panel excessively.

      2. Using a piece of cloth, rub the double-sided tape off the back door panel while it is hot from the infrared light.

        Note

        Installing the No. 2 luggage compartment door name plate while any double-sided tape remains on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

      3. Using a non-residue solvent, clean the attachment surface.

    2. Install a new No. 2 luggage compartment door name plate as shown in the illustration.

      A004E5TN01
      Installation Position
      Area Measurement Area Measurement
      A 43.0 mm (1.69 in.) B 69.8 mm (2.75 in.)
      C 95.1 mm (3.74 in.) D 180.9 mm (7.12 in.)

      Note

      Install the No. 2 luggage compartment door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 2 luggage compartment door name plate to 20 to 30°C (68 to 86°F) and install the No. 2 luggage compartment door name plate.