HYBRID CONTROL SYSTEM, Diagnostic DTC:P0560-117

DTC Code DTC Name
P0560-117 System Voltage

DESCRIPTION


DTC No. INF Code DTC Detection Condition Trouble Area
P0560 117

Malfunction in the hybrid vehicle control ECU back-up power source circuit

(1 trip detection logic)

  • Auxiliary battery

  • ECU-B NO. 2 fuse

  • Wire harness or connector

  • Hybrid vehicle control ECU
Related Data List
DTC No. Data List
P0560-117 +B

WIRING DIAGRAM

A01V0HGE07
*a MAIN
*b ECU-B NO. 2
*c Auxiliary Battery
*d Hybrid Vehicle Control ECU

CAUTION / NOTICE / HINT

Tech Tips

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.


  1. Turn the ignition switch to ON (IG) and wait for a few seconds.

PROCEDURE


  1. CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)


    1. A01V0I0E02
      Text in Illustration
      *A for LHD
      *B for RHD

      Check the connector connections and contact pressure of the relevant terminals for the hybrid vehicle control ECU connectors Click here.

      OK
      The connectors are connected securely and there are no contact pressure problems.

    NG

    CONNECT SECURELY

    OK

  2. CHECK AUXILIARY BATTERY TERMINAL (CONTACT PROBLEM)


    1. Check the connection of the auxiliary battery terminal.

      OK
      The terminal is connected securely and there is no contact problem.

    NG

    CONNECT SECURELY

    OK

  3. INSPECT AUXILIARY BATTERY

    Click here


    NG

    CHARGE OR REPLACE AUXILIARY BATTERY

    OK

  4. CHECK FUSE (ECU-B NO. 2)


    1. Remove the ECU-B NO. 2 fuse from the No. 2 engine room relay block.

    2. A01UYPUE01
      Text in Illustration
      *1 No. 2 Engine Room Relay Block
      *2 ECU-B NO. 2 Fuse

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      ECU-B NO. 2 fuse Ignition switch off Below 1 Ω

    3. Install the ECU-B NO. 2 fuse.


    NG

    REPLACE FUSE (ECU-B NO. 2)

    OK

  5. CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - ECU-B NO. 2 FUSE)


    1. Remove the ECU-B NO. 2 fuse from the No. 2 engine room relay block.

    2. Disconnect the hybrid vehicle control ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Note

      When taking measurements with a tester, do not apply excessive force to the tester probes to avoid damaging the fuse holder or terminals.

      A01V1FUE02
      Text in Illustration
      *1 No. 2 Engine Room Relay Block *2 ECU-B NO. 2 Fuse holder
      *a

      Rear view of wire harness connector

      (to Hybrid Vehicle Control ECU)

      		 - -
      Standard Resistance (Check for Open)
      Tester Connection Switch Condition Specified Condition
      F56-3 (BATT) - 2 (ECU-B NO. 2 fuse holder) Ignition switch off Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Switch Condition Specified Condition
      F56-3 (BATT) or 2 (ECU-B NO. 2 fuse holder) - Body ground and other terminals Ignition switch off 10 kΩ or more

    4. Install the ECU-B NO. 2 fuse.

    5. Connect the hybrid vehicle control ECU connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK HARNESS AND CONNECTOR (ECU-B NO. 2 FUSE - AUXILIARY BATTERY POSITIVE TERMINAL)


    1. Remove the ECU-B NO. 2 fuse from the No. 2 engine room relay block.

    2. A01V1GQE01
      Text in Illustration
      *1 No. 2 Engine Room Relay Block
      *2 ECU-B NO. 2 Fuse holder

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      1 (ECU-B NO. 2 fuse holder) - Body ground Always 11 to 14 V

    3. Install the ECU-B NO. 2 fuse.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. RECONFIRM DTC OUTPUT (HYBRID CONTROL)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Recheck for DTCs.

      Result
      Result Proceed to
      DTC P0560-117 is output again A
      DTC P0560-117 is not output B

      Tech Tips

      If DTC P0560-117 is output after this inspection, replace the hybrid vehicle control ECU. If the DTC is not output, check for intermittent problems Click here because there may be a malfunction in the wire harness or connector.


    A

    REPLACE HYBRID VEHICLE CONTROL ECU Click here

    B

    CHECK FOR INTERMITTENT PROBLEMS Click here