HAZARD WARNING SWITCH REMOVAL


  1. PRECAUTION (w/ Navigation System for HDD)

    Note

    After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

    Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal
    Specification Waiting Time
    w/o Telematics transceiver 60 sec.
    w/ Telematics transceiver 120 sec.

  2. REMOVE REAR DECK FLOOR BOX (w/ Air Suspension)


    1. A01NDSY

      Remove the 3 clips and the rear deck floor box.

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Air Suspension)

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A01NGN8

      Turn the shift lever knob sub-assembly counterclockwise and remove the shift lever knob sub-assembly.

  5. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. A01NGRU

      Move the shift lever to N.

    2. Pull the upper console panel sub-assembly in the direction indicated by the arrow to disengage the 4 claws and 4 clips.

    3. w/o Seat Heater System:


      1. Disconnect the connector from the console box hole cover.

    4. A01NDQX

      w/ Seat Heater System:


      1. Disengage the 4 claws.

      2. Disconnect the connector and remove the seat heater switch assembly.

    5. A01NEP7

      Pull the upper console panel sub-assembly in the direction indicated by the arrow to disengage the 3 claws and 3 clips.

    6. Disconnect each connector.

    7. Disengage the clamp and remove the upper console panel sub-assembly.

  6. REMOVE INSTRUMENT PANEL GARNISH LH


    1. A01NGMK

      Using moulding remover B, disengage the 6 clips and remove the instrument panel garnish LH as shown in the illustration.

  7. REMOVE NO. 1 SWITCH HOLE BASE


    1. A01NFNE

      Push the No. 1 switch hole base in the direction indicated by the arrow to disengage the 4 claws and 2 guides.

    2. Disconnect each connector and remove the No. 1 switch hole base.

  8. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. A01NGE1

      Disengage the 2 claws and open the cover as shown in the illustration.

    2. A01NG78

      Remove the 2 screws <D>.

    3. Disengage the 8 clips and 2 guides.

    4. Disconnect each connector and remove the lower instrument panel finish panel sub-assembly.

  9. REMOVE INSTRUMENT PANEL FINISH PANEL


    1. A01NG2R

      Pull the instrument panel finish panel in the direction indicated by the arrow to disengage the claw, 2 clips and 2 guides, and remove the instrument panel finish panel.

  10. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL


    1. A01NHYG

      Pull the lower instrument panel finish panel in the direction indicated by the arrow to disengage the 7 clips and remove the lower instrument panel finish panel.

  11. REMOVE RADIO RECEIVER ASSEMBLY WITH REGISTER

    Note


    • The 4 bolts of the radio receiver assembly with register are installed though the service holes at the bottom in the instrument panel. Make sure to check all of them.

    • If the radio receiver assembly with register is pulled without removing the 4 bolts, it may result in damage to the radio receiver assembly with register.


    1. A01NCUBE01

      Remove the 4 bolts.

    2. Disengage the 9 clips.

    3. Disconnect each connector and remove the radio receiver assembly with register.

  12. REMOVE HAZARD WARNING SIGNAL SWITCH ASSEMBLY


    1. A01NF2H

      Disengage the 2 clamps.

    2. Using a screwdriver, disengage the 2 claws and remove the hazard warning signal switch assembly.