HEADLIGHT DIMMER SWITCH INSTALLATION

INSTALL HEADLIGHT DIMMER SWITCH ASSEMBLY
1. Using pliers, expand the clamp.
2. While holding the clamp expanded, install the headlight dimmer switch assembly as shown in the illustration.
3. Engage the claw.
4. Install the headlight dimmer switch assembly with the clamp.
5. Connect the connector.
INSTALL WINDSHIELD WIPER SWITCH ASSEMBLY
1. Engage the claw and install the windshield wiper switch assembly as shown in the illustration.
2. Connect the connector.
INSTALL SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
Note
- Do not replace the spiral cable with the battery connected and the power switch on (IG).
- Do not rotate the spiral cable with the battery connected and the power switch on (IG).
- Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.
- Do not remove the steering sensor from the spiral cable.
1. Check that the power switch is off.
2. Check that the cable is disconnected from the negative (-) battery terminal.
3. Check that the front wheels are facing straight ahead.
4. Set the turn signal switch to the neutral position.
  
  Note
  
  If it is not in the neutral position, the turn signal switch pin may snap.
5. Install the spiral cable with sensor sub-assembly with the 3 claws.
  
  Note
  
  When replacing the spiral cable with sensor sub-assembly with a new one, remove the lock pin before installing the steering wheel assembly.
6. Connect the connectors to the spiral cable with sensor sub-assembly.
  
  Note
  
  When connecting any airbag connector, take care not to damage the airbag wire harness.
INSTALL STEERING COLUMN COVER
1. Engage the claw to install the upper steering column cover.
2. Engage the 2 claws to install the lower steering column cover to the upper steering column cover.
  
  Note
  
  Do not damage the tilt and telescopic switch.
3. Install the 3 screws.
  
  Torque:
  
  2.0 N*m { 20 kgf*cm, 18 in.*lbf }
4. Text in Illustration
  
  *1 Instrument Panel Cluster Finish Panel
  
  Engage the 4 clips and 2 guides to install the instrument panel cluster finish panel to the upper steering column cover.
TURN FRONT WHEELS TO FACE STRAIGHT AHEAD
ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
1. Check that the power switch is off.
2. Check that the cable is disconnected from the negative (-) battery terminal.
  
  CAUTION:
  
  Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
3. Rotate the spiral cable counterclockwise slowly by hand until it stops.
  
  Note
  
  Do not turn the spiral cable using the airbag wire harness.
4. Text in Illustration
  
  *1 Alignment Mark
  
  Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.
  
  Note
  
  Do not turn the spiral cable using the airbag wire harness.
  
  Tech Tips
  
  The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.
INSTALL STEERING WHEEL ASSEMBLY
1. Text in Illustration
  
  *1 Matchmark
  
  Align the matchmarks on the steering wheel assembly and steering main shaft.
2. Install the steering wheel assembly set nut.
  
  Torque:
  
  50 N*m { 510 kgf*cm, 37 ft.*lbf }
3. Connect the connectors to the spiral cable sub-assembly.
INSPECT STEERING WHEEL CENTER POINT
INSTALL STEERING PAD
1. Check that the power switch is off.
2. Check that the cable is disconnected from the negative (-) battery terminal.
  
  CAUTION:
  
  Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
3. Connect the airbag connectors to the steering pad.
  Note
  
  When connecting any airbag connector, take care not to damage the airbag wire harness.
  
  Be sure to only connect the connectors to each corresponding color.
4. Push in the lock to install the airbag connector.
5. Connect the horn connector to the steering pad.
6. Text in Illustration
  
  *1 "TORX" Screw
  
  *2 Screw Case
  
  Confirm that the circumference groove of each "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.
7. Using a T30 "TORX" socket wrench, tighten the 2 "TORX" screws.
  
  Torque:
  
  8.8 N*m { 90 kgf*cm, 78 in.*lbf }
INSTALL LOWER NO. 3 STEERING WHEEL COVER
1. Engage the claw to install the lower No. 3 steering wheel cover.
INSTALL LOWER NO. 2 STEERING WHEEL COVER
1. Engage the claw to install the lower No. 2 steering wheel cover.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Note
- Make sure that the cable has been disconnected from the negative (-) battery terminal for at least 2 seconds before reconnecting the cable.
- Reset the auto tilt away function setting to the previous condition by changing the customize parameter Click here.
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
INSTALL REAR DECK FLOOR BOX
1. Install the rear deck floor box with the 3 clips.
INSPECT STEERING PAD
1. Visually check for defects with the steering pad installed on the vehicle.
  1. The defects are as follows:
    
    Cuts on the surface and in the grooves of the steering pad
    
    Small cracks on the surface and in the grooves of the steering pad
    
    Significant discoloration on the surface and in the grooves of the steering pad
    
    OK
    
    No defects are found.
    
    Tech Tips
    
    If any of the defects is found, replace the steering pad with a new one.
2. Make sure that the horn sounds.
  
  Tech Tips
  
  If the horn does not sound, inspect the horn system Click here.
INSPECT SRS WARNING LIGHT
1. Inspect the SRS warning light Click here.

Text in Illustration
*1	"TORX" Screw
*2	Screw Case