WASHER NOZZLE (for Rear Side) INSTALLATION


  1. INSTALL REAR WASHER NOZZLE


    1. A01NFFK

      Connect the washer hose.

    2. A01NF91

      Engage the 2 claws to install the rear washer nozzle.

  2. INSPECT REAR WASHER NOZZLE


    1. With the engine running, check that the center stream of washer fluid sprays on the windshield within the hatched area shown in the illustration.

      Standard
      Washer fluid hits the windshield in the area shown in the illustration.
      A01NG2PE01
      Standard Clearance
      Area Measurement
      A 43 mm (1.693 in.)
      B 50 mm (1.969 in.)
      C 40 mm (1.575 in.)
      D 150 mm (5.906 in.)

      Tech Tips

      If the result is not as specified, replace the malfunctioning rear washer nozzle.

  3. ADJUST REAR WASHER NOZZLE


    1. A01NEGF

      Using a screwdriver, adjust the direction of the rear washer nozzle.

      Note

      Do not use a safety pin or other pointed tools. Doing so may damage the inside of the washer nozzle.

      Tech Tips

      Use a thin-bladed screwdriver with an approximately 1 mm (0.0394 in.) thick tip.

  4. INSTALL REAR WIPER MOTOR AND BRACKET ASSEMBLY


    1. A01NF83

      Install the rear wiper motor and bracket assembly with the 3 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

    2. Connect the connector.

    3. Engage the clamp.

  5. INSTALL REAR WIPER MOTOR GROMMET


    1. A01NHF0E05
      Text in Illustration
      *1 MP grease

      Apply MP grease to the entire surface of the rear wiper motor grommet lip.

      Tech Tips

      Make sure that the hole does not get clogged with grease and the grooves on the lip are filled with grease.

    2. A01NGHL

      Install the rear wiper motor grommet.

  6. INSTALL REAR WIPER ARM AND BLADE ASSEMBLY


    1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

    2. When reusing the rear wiper arm and blade assembly:


      1. A01NHR2E03
        Text in Illustration
        *1 Wiper Arm Serration

        Clean the wiper arm serrations.

    3. When reusing the rear wiper motor assembly:


      1. A01NELBE03
        Text in Illustration
        *1 Wire Brush
        *2 Wiper Pivot Serration

        Clean the wiper pivot serrations with a wire brush.

    4. A01NF9TE01
      Text in Illustration
      *1 Ceramic Line

      Install the rear wiper arm and blade assembly with the nut to the position shown in the illustration.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
      Standard Clearance
      Area Measurement
      A 30 mm (1.181 in.)

      Tech Tips

      Hold the wiper arm by hand while tightening the nut.

    5. Operate the rear wiper while spraying washer fluid onto the back door glass. Make sure that the rear wiper functions properly and the wiper does not come into contact with the vehicle body.

  7. INSTALL REAR SPOILER SUB-ASSEMBLY


    1. Install the 2 pins.

    2. Install a new clip.

    3. A01NHE7

      Engage the clip and 2 pins to install the rear spoiler sub-assembly.

    4. A01NFME

      Install the 5 nuts.

      Torque:
      5.9 N*m  { 60 kgf*cm, 52 in.*lbf }

    5. Install the 2 hole plugs.

    6. Connect each connector.

  8. INSTALL UPPER BACK WINDOW PANEL TRIM


    1. A01NGB3E01
      Text in Illustration
      *1 2-piece Type Clip

      Engage the 7 clips and 6 claws to install the upper back window panel trim.