OUTER REAR VIEW MIRROR INSTALLATION


  1. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY


    1. A01NH8M

      Engage the claw to install the outer rear view mirror assembly as shown in the illustration.

    2. w/o Side Monitor System:


      1. A01NEN5

        Install the 3 nuts.

        Torque:
        5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      2. Engage the clamp as shown in the illustration.

    3. w/ Side Monitor System:


      1. A01NHFB

        Install the 3 nuts.

        Torque:
        5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      2. Engage the clamp as shown in the illustration.

      3. Connect the connector.

  2. INSTALL OUTER MIRROR INSTALL HOLE COVER


    1. A01NE09

      Engage the 2 claws and 2 guides to install the outer mirror install hole cover as shown in the illustration.

  3. INSTALL OUTER MIRROR PROTECTOR


    1. A01NGHH

      Install a new outer mirror protector.

  4. INSTALL FRONT DOOR SERVICE HOLE COVER


    1. Apply butyl tape to the front door panel.

    2. A01NEQQE01
      Text in Illustration
      *1 Reference Point

      Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.

    3. Attach the front door service hole cover according to the reference points on the front door panel.

      Note

      Securely install the front door service hole cover preventing wrinkles and air bubbles.

    4. Connect the connector.

  5. INSTALL NO. 1 FRONT DOOR TRIM BRACKET


    1. A01NE1N

      Install the 2 bolts and No. 1 front door trim bracket.

  6. INSTALL OUTER MIRROR CONTROL ECU ASSEMBLY


    1. A01NGS7

      Install the outer mirror control ECU assembly with the 2 screws.

    2. Connect each connector.

  7. INSTALL NO. 3 FRONT SPEAKER ASSEMBLY


    1. A01NEQH

      Engage the clip and temporarily install the front No. 3 speaker assembly.

    2. Install the front No. 3 speaker assembly with the 2 screws.

    3. Connect the connector.

  8. INSTALL DOOR FRAME GARNISH


    1. A01NHUV

      Install the door frame garnish with the 2 clips.

  9. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP


    1. A01NES8

      Engage the 4 claws and install the front door inner glass weatherstrip as shown in the illustration.

  10. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. Install a new front door trim board retainer (green).

    2. A01NGMN

      Connect the front door lock remote control cable assembly and front door inside locking cable assembly.

    3. Connect each connector.

    4. A01ND88

      Engage the front door trim board sub-assembly with the 4 claws of the front door inner glass weatherstrip as shown in the illustration.

    5. A01NFFCE01
      Text in Illustration
      *1 Front Door Trim Board Retainer

      Engage the 10 clips, front door trim board retainer and install the front door trim board sub-assembly.

    6. Install the 3 screws.

      Torque:
      (A)
      3.5 N*m  { 36 kgf*cm, 31 in.*lbf }

  11. INSTALL NO. 1 FRONT DOOR STIFFENER CUSHION


    1. A01NCRL

      Install the No. 1 front door stiffener cushion with the screw.

  12. INSTALL COURTESY LIGHT ASSEMBLY


    1. Connect the connector.

    2. A01NCMHE01

      Engage the claw to install the courtesy light assembly.

  13. INSTALL DOOR ARMREST COVER


    1. A01NHCO

      Install the door armrest cover.

  14. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    1. A01NHHO

      Connect the connector.

    2. Engage the 2 clips and 5 claws, and install the power window regulator master switch assembly with front door armrest base panel.

  15. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    1. A01NF52

      Connect the connector.

    2. Engage the 2 clips and 5 claws, and install the power window regulator switch assembly with front door armrest base panel.

  16. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. A01NG38

      Engage the 3 claws and install the front door inside handle bezel plug.

  17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  18. INSTALL REAR DECK FLOOR BOX


    1. A01NDSY

      Install the rear deck floor box with the 3 clips.

  19. ADJUST SIDE TELEVISION CAMERA OPTICAL AXIS (CAMERA POSITION SETTING) (w/ Parking Assist Monitor System)

    Click here.