OUTER REAR VIEW MIRROR INSPECTION


  1. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH


    1. A01NEJWE05
      Text in Illustration
      *1

      Component without harness connected

      (Outer Rear View Mirror Assembly RH)

      Inspect outer mirror motor operation.


      1. Apply auxiliary battery voltage and check the operation of the mirror face, as shown in the table and illustration.

        Standard
        Measurement Condition Specified Condition

        Auxiliary battery positive (+) → Terminal 1 (RMVR)

        Auxiliary battery negative (-) → Terminal 10 (RM+R)

        		 Turns upward (A)

        Auxiliary battery positive (+) → Terminal 10 (RM+R)

        Auxiliary battery negative (-) → Terminal 1 (RMVR)

        		 Turns downward (B)

        Auxiliary battery positive (+) → Terminal 9 (RMHR)

        Auxiliary battery negative (-) → Terminal 10 (RM+R)

        		 Turns left (C)

        Auxiliary battery positive (+) → Terminal 10 (RM+R)

        Auxiliary battery negative (-) → Terminal 9 (RMHR)

        		 Turns right (D)

        If the result is not as specified, replace the outer rear view mirror assembly RH.

    2. Inspect outer mirror heater operation.


      1. Apply auxiliary battery voltage and check the operation of the mirror face, as shown in the table below.

        Standard
        Measurement Condition Specified Condition

        Auxiliary battery positive (+) → Terminal 4 (HTR+)

        Auxiliary battery negative (-) → Terminal 12 (HTR-)

        		 Mirror surface temperature becomes higher

        If the result is not as specified, replace the outer rear view mirror assembly RH.

    3. A01NEB8E01
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Outer Mirror Control ECU)
      *2 Bright
      *3 Dark

      Inspect electrochromic outer mirror operation.


      1. Apply auxiliary battery voltage and check the operation of the mirror face, as shown in the table and illustration.

        Standard
        Measurement Condition Specified Condition

        Auxiliary battery positive (+) → Terminal 7 (EC+)

        Auxiliary battery negative (-) → Terminal 15 (EC-)

        		 Mirror surface changes to dark

        If the result is not as specified, replace the outer rear view mirror assembly RH.

  2. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH


    1. A01NFMLE07

      Inspect outer mirror motor operation.


      1. Remove the outer rear view mirror assembly.

      2. Apply auxiliary battery voltage and check the operation of the mirror face, as shown in the table and illustration.

        Standard
        Measurement Condition Specified Condition

        Auxiliary battery positive (+) → Terminal 1 (LMVR)

        Auxiliary battery negative (-) → Terminal 10 (LM+R)

        		 Turns upward (A)

        Auxiliary battery positive (+) → Terminal 10 (LM+R)

        Auxiliary battery negative (-) → Terminal 1 (LMVR)

        		 Turns downward (B)

        Auxiliary battery positive (+) → Terminal 9 (LMHR)

        Auxiliary battery negative (-) → Terminal 10 (LM+R)

        		 Turns left (C)

        Auxiliary battery positive (+) → Terminal 10 (LM+R)

        Auxiliary battery negative (-) → Terminal 9 (LMHR)

        		 Turns right (D)

        If the result is not as specified, replace the outer rear view mirror assembly LH.

    2. Inspect outer mirror heater operation.


      1. Apply auxiliary battery voltage and check the operation of the mirror face, as shown in the table below.

        Standard
        Measurement Condition Specified Condition

        Auxiliary battery positive (+) → Terminal 4 (HTR+)

        Auxiliary battery negative (-) → Terminal 12 (HTR-)

        		 Mirror surface temperature becomes higher

        If the result is not as specified, replace the outer rear view mirror assembly LH.

    3. A01NEE1E02
      Text in Illustration
      *1

      Component without harness connected

      (Outer Rear View Mirror Assembly LH)
      *2 Bright
      *3 Dark

      Inspect electrochromic outer mirror operation.


      1. Apply auxiliary battery voltage and check the operation of the mirror face, as shown in the table and illustration.

        Standard
        Measurement Condition Specified Condition

        Auxiliary battery positive (+) → Terminal 7 (EC+)

        Auxiliary battery negative (-) → Terminal 15 (EC-)

        		 Mirror surface changes to dark

        If the result is not as specified, replace the outer rear view mirror assembly LH.