POWER MIRROR CONTROL SYSTEM Front Passenger Side Power Mirror cannot be Adjusted with Power Mirror Switch

SYSTEM DESCRIPTION

When the mirror adjust switch is operated, the multiplex network master switch assembly detects the switch operation and sends the mirror adjust switch signal to the main body ECU (multiplex network body ECU) via LIN communication. The main body ECU (multiplex network body ECU) then sends the mirror adjust switch signal to the outer mirror control ECU (front passenger side) via CAN communication. On receiving the signal, the outer mirror control ECU (front passenger side) operates the vertical and horizontal mirror motors, which are built into the outer rear view mirror assembly (front passenger side), to adjust the mirror surface position.

WIRING DIAGRAM

A01NDM1E07

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK CAN COMMUNICATION SYSTEM


    1. Use the intelligent tester to check if the CAN communication system is functioning normally Click here.

      OK
      Multiplex communication DTC is not output.

    NG

    GO TO CAN COMMUNICATION SYSTEM (DIAGNOSTIC TROUBLE CODE CHART) Click here

    OK

  2. READ VALUE USING INTELLIGENT TESTER (OUTER MIRROR SWITCH)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Master Switch / Data List.

    5. for LHD:


      1. Read the Data List according to the display on the intelligent tester.

        Master Switch
        Tester Display Measurement Item/Range Normal Condition Diagnostic Note
        Mirror Selection SW (R) Mirror select switch signal for RH mirror / ON or OFF

        ON: Switch in R position

        OFF: Switch off or in L position

        		 -
        Mirror Position SW (R) Mirror adjust switch signal (right) / ON or OFF

        ON: Mirror adjust switch pressed right

        OFF: Mirror adjust switch not pressed right

        		 Check with the mirror select switch in the R position
        Mirror Position SW (L) Mirror adjust switch signal (left) / ON or OFF

        ON: Mirror adjust switch pressed left

        OFF: Mirror adjust switch not pressed left

        		 Check with the mirror select switch in the R position
        Mirror Position SW (Up) Mirror adjust switch signal (up) / ON or OFF

        ON: Mirror adjust switch pressed up

        OFF: Mirror adjust switch not pressed up

        		 Check with the mirror select switch in the R position
        Mirror Position SW (Dwn) Mirror adjust switch signal (down) / ON or OFF

        ON: Mirror adjust switch pressed down

        OFF: Mirror adjust switch not pressed down

        		 Check with the mirror select switch in the R position
        OK
        On the intelligent tester screen, ON or OFF is displayed for each item according to the table above.

    6. for RHD:


      1. Read the Data List according to the display on the intelligent tester.

        Master Switch
        Tester Display Measurement Item/Range Normal Condition Diagnostic Note
        Mirror Selection SW (L) Mirror select switch signal for LH mirror / ON or OFF

        ON: Switch in L position

        OFF: Switch off or in R position

        		 -
        Mirror Position SW (R) Mirror adjust switch signal (right) / ON or OFF

        ON: Mirror adjust switch pressed right

        OFF: Mirror adjust switch not pressed right

        		 Check with the mirror select switch in the L position
        Mirror Position SW (L) Mirror adjust switch signal (left) / ON or OFF

        ON: Mirror adjust switch pressed left

        OFF: Mirror adjust switch not pressed left

        		 Check with the mirror select switch in the L position
        Mirror Position SW (Up) Mirror adjust switch signal (up) / ON or OFF

        ON: Mirror adjust switch pressed up

        OFF: Mirror adjust switch not pressed up

        		 Check with the mirror select switch in the L position
        Mirror Position SW (Dwn) Mirror adjust switch signal (down) / ON or OFF

        ON: Mirror adjust switch pressed down

        OFF: Mirror adjust switch not pressed down

        		 Check with the mirror select switch in the L position
        OK
        On the intelligent tester screen, ON or OFF is displayed for each item according to the table above.

    NG

    REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY Click here

    OK

  3. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER MIRROR CONTROL FUNCTION)


    1. for LHD: Enter the following menus: Body / Mirror R / Active Test.

    2. for RHD: Enter the following menus: Body / Mirror L / Active Test.

    3. Perform the Active Test according to the display on the intelligent tester.

      Mirror R / Mirror L
      Tester Display Test Part Control Range Diagnostic Note
      Mirror Up/Down Mirror vertical operation Up / Down -
      Mirror Right/Left Mirror horizontal operation Right / Left -
      OK
      Power mirror operation is normal.

    NG

    INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER SIDE) Click here

    OK

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER SIDE) Click here

  4. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER SIDE)


    1. for LHD:


      1. A01NEJWE01
        Text in Illustration
        *1

        Component without harness connected

        (Outer Rear View Mirror Assembly LH)

        Remove the outer rear view mirror assembly RH Click here.

      2. Apply auxiliary battery voltage and check the operation of the outer rear view mirror assembly RH.

        OK
        Measurement Condition Specified Condition

        Auxiliary battery positive (+) → Terminal z3-1 (RMVR)

        Auxiliary battery negative (-) → Terminal z3-10 (RM+R)

        		 Turns upward

        Auxiliary battery negative (-) → Terminal z3-1 (RMVR)

        Auxiliary battery positive (+) → Terminal z3-10 (RM+R)

        		 Turns downward

        Auxiliary battery positive (+) → Terminal z3-9 (RMHR)

        Auxiliary battery negative (-) → Terminal z3-10 (RM+R)

        		 Turns left

        Auxiliary battery negative (-) → Terminal z3-9 (RMHR)

        Auxiliary battery positive (+) → Terminal z3-10 (RM+R)

        		 Turns right

    2. for RHD:


      1. A01NFMLE06
        Text in Illustration
        *1

        Component without harness connected

        (Outer Rear View Mirror Assembly RH)

        Remove the outer rear view mirror assembly LH Click here.

      2. Apply auxiliary battery voltage and check the operation of the outer rear view mirror assembly LH.

        OK
        Measurement Condition Specified Condition

        Auxiliary battery positive (+) → Terminal z4-1 (LMVR)

        Auxiliary battery negative (-) → Terminal z4-10 (LM+R)

        		 Turns upward

        Auxiliary battery negative (-) → Terminal z4-1 (LMVR)

        Auxiliary battery positive (+) → Terminal z4-10 (LM+R)

        		 Turns downward

        Auxiliary battery positive (+) → Terminal z4-9 (LMHR)

        Auxiliary battery negative (-) → Terminal z4-10 (LM+R)

        		 Turns left

        Auxiliary battery negative (-) → Terminal z4-9 (LMHR)

        Auxiliary battery positive (+) → Terminal z4-10 (LM+R)

        		 Turns right

    NG

    REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER SIDE) Click here

    OK

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER SIDE) Click here