REAR SEAT OUTER BELT ASSEMBLY DISPOSAL

Tech Tips

When scrapping vehicles equipped with a seat belt pretensioner or disposing of a rear seat outer belt (with a seat belt pretensioner), always deploy the seat belt pretensioner first in accordance with the procedures described below. If any abnormality occurs during deployment of the seat belt pretensioner, contact the service dept. of the distributor.


  1. DISPOSE OF REAR SEAT OUTER BELT ASSEMBLY (WHEN INSTALLED IN VEHICLE)

    CAUTION:


    • Use gloves and safety glasses when handling a rear seat outer belt with a deployed pretensioner.

    • Always wash your hands with water after completing the operation.

    • Do not apply water, etc. to a rear seat outer belt with a deployed pretensioner.

    • When deploying the seat belt pretensioner, always use the specified SST (SRS airbag deployment tool). Perform the operation in a place away from electrical interference.

    Note


    • Never dispose of a rear seat outer belt assembly with a pretensioner that has not been deployed.

    • The seat belt pretensioner produces an exploding sound when it deploys, so perform the operation outdoors when it will not disturb local residents.

    • When deploying a rear seat outer belt (with a seat belt pretensioner), perform the operation at least 10 m (33 ft.) away from the rear seat outer belt.

    • Be sure to follow the procedure listed below when deploying the seat belt pretensioner.


    1. A01NEYLE11

      Check the function of SST.

      SST
      09082-00700

      Note

      When deploying the seat belt pretensioner, always use the specified SST.


      1. A01NFYPE10

        Connect the red clip of SST to the battery positive (+) terminal and the black clip to the battery negative (-) terminal.

        Tech Tips

        At this time, do not connect the yellow connected that will later be connect to the seat belt pretensioner.

      2. A01NF3XE10

        Press the SST deployment switch and check that the LED of the SST deployment switch illuminates.

        CAUTION:

        If the LED is illuminated when the deployment switch is not pressed, SST may be malfunctioning. In this case, do not use SST.

    2. Connect SST.


      1. A01NDZCE01

        Connect 2 SST, and then connect them to the rear seat outer belt pretensioner.

        SST
        09082-00700
        09082-00770

        Note

        To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the pretensioner connector.

      2. A01NGFQE06

        Move SST at least 10 m (33 ft.) away from the rear of the vehicle.

      3. Close all the doors and windows of the vehicle.

        Note

        Do not damage the SST wire harness.

    3. Deploy the rear seat outer belt pretensioner.


      1. Confirm that no one is inside the vehicle or within a 10 m (33 ft.) radius of the vehicle.

      2. Connect the red clip of SST to the battery positive (+) terminal and the black clip to the negative (-) terminal.

      3. Press the SST deployment switch to deploy the rear seat outer belt pretensioner.

        Tech Tips

        The seat belt pretensioner will deploy at the same time as the LED of SST illuminates.

    4. A01NI0H

      Dispose of the rear seat outer belt assembly.


      1. Remove the rear seat outer belt assembly and SST.

      2. Place the outer belt in a plastic bag, tie the end tightly, and dispose of it in the same way as other general parts.

        CAUTION:


        • The outer belt becomes very hot when the rear seat outer belt pretensioner is deployed, so leave it untouched for at least 30 minutes after it has been deployed.

        • Use gloves and safety glasses when handling an outer belt with handling an outer belt with a pretensioner that has been deployed.

        • Always wash your hands with water after completing the operation.

        • Do not apply water, etc. to a rear seat outer belt assembly with a pretensioner that has been deployed.

        Tech Tips

        When scrapping a vehicle, deploy the rear seat outer belt pretensioners, and then scrap the vehicle with the deployed outer belt installed.

  2. DISPOSE OF REAR SEAT OUTER BELT ASSEMBLY (WHEN NOT INSTALLED IN VEHICLE)

    CAUTION:


    • Use gloves and safety glasses when handling a rear seat outer belt with a deployed pretensioner.

    • Always wash your hands with water after completing the operation.

    • Do not apply water, etc. to a rear seat outer belt with a deployed pretensioner.

    • When disposing of a pretensioner equipped rear seat outer belt, never deploy the belt in the customer's vehicle.

    Note


    • Never dispose of a rear seat outer belt assembly with a pretensioner that has not been deployed.

    • The seat belt pretensioner produces an exploding sound when it deploys, so perform the operation outdoors where it will not disturb local residents.

    • When deploying a rear seat outer belt (with a seat belt pretensioner), perform the operation at least 10 m (33 ft.) away from the rear seat outer belt.

    • Be sure to follow the procedure listed below when deploying the seat belt pretensioner.


    1. A01NEYLE12

      Check the function of SST.

      SST
      09082-00700

      CAUTION:

      When deploying the seat belt pretensioner, always use the specified SST.


      1. A01NFYPE10

        Connect the red clip of SST to the battery positive (+) terminal and the black clip to the battery negative (-) terminal.

        Tech Tips

        At this time, do not connect the yellow connector that will later be connected to the seat belt pretensioner.

      2. A01NF3XE10

        Press the SST deployment switch and check that the LED of the SST deployment switch illuminates.

        CAUTION:

        If the LED is illuminated when the deployment switch is not pressed, SST may be malfunctioning. In this case, do not use SST.

    2. A01NDZCE01

      Connect SST.

      SST
      09082-00700
      09082-00770

      1. Connect 2 SST, and then connect them to the rear seat outer belt pretensioner.

        Note

        To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the pretensioner connector.

      2. Place the outer belt on the ground and cover it with a tire and wheel assembly.

        Note

        Position the rear seat outer belt assembly as shown in the illustration.

      3. Position and hold SST at least 10 m (33 ft.) away from the wheel.

        Note

        Do not damage the SST wire harness.

    3. A01NGM6E08

      Depose of the rear seat outer belt pretensioner.


      1. Check that no one is within a 10 m (33 ft.) radius of the wheel.

      2. connect the red clip of SST to the battery positive (+) terminal and the black clip to the battery negative (-) terminal.

      3. Press the SST deployment switch to deploy the rear seat outer belt pretensioner.

        Tech Tips

        The seat belt pretensioner will deploy at the same time as the LED of SST illuminates.

    4. A01NI0H

      Dispose of the rear seat outer belt assembly.


      1. Remove the wheel and SST.

      2. Place the outer belt in a plastic bag, tie the end tightly, and dispose of it in the same way as other general parts.

        CAUTION:


        • The outer belt becomes very hot when the rear seat outer belt pretensioner is deployed, so leave it untouched for at least 30 minutes after it has been deployed.

        • Use gloves and safety glasses when handling an outer belt with a pretensioner that has been deployed.

        • Always wash your hands with water after completing the operation.

        • Do not apply water, etc. to a rear seat outer belt assembly with a pretensioner that has been deployed.

        Tech Tips

        When Scrapping a vehicle, deploy the rear seat outer belt pretensioners, and then scrap the vehicle with the deployed outer belt installed.