FRONT SEAT ASSEMBLY REASSEMBLY


  1. INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY

    CAUTION:


    • The nuts must not be reused.

    • Make sure that the front seat frame assembly with adjuster is not deformed. If it is, replace it with a new one.


    1. A01NCOA

      Install the front seat side airbag assembly with 2 new nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
    2. A01NDBN

      Engage the 2 clamps.

    3. A01NFRI

      Engage the 3 clamps to install the wire harness.

  2. INSTALL FRONT SEAT WIRE


    1. A01NFC8

      Engage the 8 clamps and install the front seat wire to the front seat frame assembly with adjuster.

    2. Connect the 3 connectors.

    3. A01NDZX

      Engage the 3 clamps and install the front seat wire.

    4. Connect the connector.

    5. w/ Rear Seat Entertainment System:


      1. A01NHB5

        Engage the 5 clamps.

  3. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Climate Control Seat System)


    1. A01NFYS

      Engage the 2 guides and install the seat heater control sub-assembly.

    2. Connect the connector.

  4. INSTALL SEAT POSITION SENSOR


    1. A01NHB7

      Install the seat position sensor to the seat slide position sensor protector with the pin as shown in the illustration.

    2. A01NGSLE12
      Text in Illustration
      *1 Seat Position Sensor
      *2 Feeler Gauge
      *3 Seat Rail

      Using a 1.3 mm (0.0512 in.) feeler gauge, temporarily install the seat position sensor.

      Note


      • If the seat position sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position sensor with a new one.

      • When installing the seat position sensor, be careful that the SRS wiring does not interfere with or is pinched between other parts.

      Tech Tips

      Be sure that the clearance between the seat position sensor and seat rail is between 0.6 mm (0.0236 in.) and 2.0 mm (0.0787 in.).

    3. A01NDEA

      Using a T30 "TORX" socket wrench, tighten the "TORX" screw to install the seat position sensor.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    4. Make sure that the clearance between the seat position sensor and seat rail is between 0.6 mm (0.0236 in.) and 2.0 mm (0.0787 in.).

    5. Connect the connector.

    6. Check that there is no looseness in the installation parts of the seat position sensor.

  5. INSTALL SEAT CUSHION CLIMATE CONTROL BLOWER (w/ Climate Control Seat System)


    1. A01NGLV

      Engage the 2 hooks and temporarily install the seat cushion climate control blower.

    2. Install the screw.

    3. Connect the connector and install the seat cushion climate control blower as shown in the illustration.

  6. INSTALL SEAT CUSHION CLIMATE CONTROL DUCT (w/ Climate Control Seat System)


    1. A01NHPVE02

      Engage the 2 claws.

    2. Engage the 2 clamps (A) in the direction indicated by the arrow.

    3. Engage the 2 clamps (B) in the direction indicated by the arrow and install the seat cushion climate control duct.

  7. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH


    1. A01NDYPE01
      Text in Illustration
      *1 Hook
      *2 Guide

      Engage the guide.

    2. Engage the hook as shown in the illustration.

    3. Install the front seat lower cushion shield RH with the screw.

  8. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH


    1. A01NG4KE02
      Text in Illustration
      *1 Hook
      *2 Guide

      Engage the guide.

    2. Engage the hook as shown in the illustration.

    3. Install the front seat lower cushion shield LH with the screw.

  9. INSTALL UPPER RECLINING ADJUSTER INSIDE COVER RH


    1. A01NGUU

      Engage the guide.

    2. Install the upper reclining adjuster inside cover RH with the screw.

  10. INSTALL LOWER RECLINING ADJUSTER INSIDE COVER RH


    1. A01NE9UE02
      Text in Illustration
      *1 Guide
      *2 Clamp

      Engage the guide.

    2. Engage the clamp and install the side airbag wire harness.

    3. Install the lower reclining adjuster inside cover RH with the 2 screws.

  11. INSTALL UPPER RECLINING ADJUSTER INSIDE COVER LH


    1. A01NFIS

      Engage the guide.

    2. Install the upper reclining adjuster inside cover LH with the screw.

  12. INSTALL LOWER RECLINING ADJUSTER INSIDE COVER LH


    1. A01NDVVE02
      Text in Illustration
      *1 Guide
      *2 Clamp

      Engage the guide.

    2. Install the lower reclining adjuster inside cover LH with the 2 screws.

    3. Engage the clamp and install the side airbag wire harness.

  13. INSTALL ACTIVE HEADREST LOWER UNIT


    1. A01NFB0

      Install the active headrest lower unit with the 2 nuts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  14. INSTALL ACTIVE HEADREST UPPER UNIT


    1. A01NCVLE01

      Install the active headrest upper unit with the 4 nuts <B>.

      Torque:
      14 N*m  { 143 kgf*cm, 10 ft.*lbf }

    2. Connect the cable to the active headrest upper unit with the nut <A> as shown in the illustration.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  15. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY


    1. A01NH1G

      Install the bush.

    2. A01NH3E

      Engage the guide.

    3. Install the lumbar support adjuster assembly with the 2 screws.

    4. Connect the connector.

    5. A01NDQB

      Engage the 2 clamps as shown in the illustration.

    6. A01NDV0

      Engage the 4 guides and install the front seatback spring sub-assembly.

    7. A01NGKD

      Engage the 4 guides to install the seatback felt.

  16. INSTALL SEATBACK CLIMATE CONTROL BLOWER (w/ Climate Control Seat System)


    1. A01NFY2

      Using a T30 ''TORX'' socket, install the seatback climate control blower and the seatback climate control cover to the seat frame with the 6 ''TORX'' bolts.

      Torque:
      2.6 N*m  { 27 kgf*cm, 23 in.*lbf }

    2. for Driver Side:


      1. A01NGIV

        Engage the 3 clamps and install the wire harness.

      2. Connect the connector.

    3. for Front Passenger Side:


      1. A01NHDW

        Engage the clamp and install the wire harness.

      2. Connect the connector.

  17. INSTALL FRONT SEATBACK HEATER ASSEMBLY (w/ Climate Control Seat System)


    1. A01ND5J

      Using a tacker, install the front seatback heater assembly to the end of the seat cover with the 12 tack pins.

      Note


      • Be careful not to damage the cover.

      • When installing the tack pins, take care to minimize wrinkles as much as possible.

  18. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    1. A01NGFM

      Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 14 new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

  19. INSTALL FRONT SEATBACK COVER WITH PAD


    1. A01NG97E01
      Text in Illustration
      *1 Side Airbag

      Temporarily install the side airbag so that it is stored inside the separate type front seatback cover with pad.

      Note

      Make sure that the side airbag is stored inside the pad correctly. Otherwise the side airbag may not deploy properly.

    2. Install bracket A onto the bolt.

      A01NDHSE01
      Text in Illustration
      *1 Bracket A *2 Bracket B

    3. Install bracket B onto the bolt and insert the guide.

    4. Install the front seatback cover bracket with the nut.

      Torque:
      5.6 N*m  { 57 kgf*cm, 50 in.*lbf }

      CAUTION:


      • For vehicles with side airbags, the seatback cover must be securely installed. Otherwise, the side airbags may not deploy properly.

      • Make sure that the strap is not twisted after installing the bracket.

      • Install the bracket securely.

    5. A01NF7W

      Engage the 6 hooks as shown in the illustration.

    6. A01NFCN

      Using hog ring pliers, install the seatback cover to the seat frame with 5 new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

    7. A01NHUH

      Engage the 2 hooks and install the front seatback cover with pad.

  20. INSTALL FRONT SEAT HEADREST SUPPORT


    1. A01NG1Y

      Engage the 4 claws and install the 2 front seat headrest supports.

  21. INSTALL FRONT SEATBACK BOARD COVER SUB-ASSEMBLY


    1. A01NE5Q

      Engage the 2 hooks to install the front seatback board cover sub-assembly.

  22. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY


    1. A01NEFN

      Engage the 2 guides as shown in the illustration.

    2. A01NDDM

      Install the front setback board sub-assembly with the 2 screws.

  23. INSTALL NO. 2 TELEVISION BASE (w/ Rear Seat Entertainment System)


    1. A01NF1B

      Engage the 2 guides.

    2. Install the 5 clips.

    3. A01NDNX

      Install the No. 2 television base with the 4 screws.

  24. INSTALL TELEVISION DISPLAY ASSEMBLY WITH COVER (w/ Rear Seat Entertainment System)


    1. A01NDQU

      Install the television display assembly with the 3 nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

    2. Connect the connector.

  25. INSTALL TELEVISION BASE COVER CAP (w/ Rear Seat Entertainment System)


    1. A01NE8I

      Engage the 3 guides and 3 claws to install the television base cover cap.

  26. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY (w/ Climate Control Seat System)


    1. A01NG9T

      Using a tacker, install the front seat cushion heater assembly to the end of the seat cover with the 30 tack pins.

      Note


      • Be careful not to damage the cover.

      • When installing the tack pins, take care to minimize wrinkles as much as possible.

  27. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER (w/o Seat Cushion Front Edge Adjustment Function)


    1. A01NGPE

      Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 19 new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

    2. A01NG6O

      Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 2 new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

  28. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER (w/ Seat Cushion Front Edge Adjustment Function)


    1. A01NHGS

      Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 15 new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

    2. A01NG6O

      Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 2 new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

  29. INSTALL FRONT SEAT CUSHION COVER WITH PAD (w/o Seat Cushion Front Edge Adjustment Function)


    1. w/o Climate Control Seat System:


      1. A01NFJ9

        Engage the 5 clamps.

    2. w/ Climate Control Seat System:


      1. A01NEUM

        Engage the 6 clamps.

      2. Connect the 2 connectors.

    3. for Front Passenger Side:


      1. A01NE0K

        Engage the 2 clamps and connect the occupant detection sensor connector.

    4. Engage each hook as shown in the illustration.

      A01NDC2

    5. Install the 2 clips.

    6. A01NDMT

      Engage the 6 hooks and install the front seat cushion cover with pad.

  30. INSTALL FRONT SEAT CUSHION COVER WITH PAD (w/ Seat Cushion Front Edge Adjustment Function)


    1. A01NG72

      Using hog ring pliers, install 2 new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

    2. A01ND0G

      Engage the 4 hooks.

    3. Engage each hook as shown in the illustration.

      A01NEVW

    4. for Front Passenger Side:


      1. A01NE0K

        Engage the 2 clamps and connect the occupant detection sensor connector.

    5. Install the 2 clips.

    6. A01NDMT

      Engage the 6 hooks and install the front seat cushion cover with pad.

  31. INSTALL POWER SEAT SWITCH


    1. A01NEDR

      Connect the 2 connectors.

    2. A01ND2C

      Engage the guide.

    3. Install the power seat switch with the 3 screws.

  32. INSTALL FRONT SEAT CUSHION INNER SHIELD


    1. A01NEFC

      Engage the guide and temporarily install the front seat cushion inner shield as shown in the illustration.

    2. A01NGRF

      Engage the claw.

    3. Install the front seat cushion inner shield with the screw.

  33. INSTALL SEAT VARIABLE CUSHION SWITCH (w/ Seat Cushion Front Edge Adjustment Function)


    1. A01NFBK

      Install the seat variable cushion switch with the 2 screws.

  34. INSTALL LUMBAR SWITCH


    1. A01NHGW

      Install the lumbar switch with the 2 screws.

  35. INSTALL NO. 1 FRONT SEAT CUSHION INNER SHIELD


    1. A01NFPW

      Engage the 2 guides as shown in the illustration.

    2. Install the No. 1 front seat cushion inner shield with the 2 screws.

  36. INSTALL FRONT SEAT CUSHION SHIELD ASSEMBLY


    1. w/ Seat Cushion Front Edge Adjustment Function:


      1. A01NG4V

        Connect the connector.

      2. Engage the 2 clamps to the install the seat wire to front seat cushion shield assembly with seat variable cushion switch.

    2. A01NEMB

      Connect the connector to the lumbar switch.

    3. A01NHTE

      Engage the guide and claw.

    4. Install the front seat cushion shield assembly with the 5 screws.

    5. A01NFR1

      Engage the 2 hooks and install the 2 rubber bands of the front seatback board to the seat frame.

  37. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    1. A01NDGN

      Engage the 4 claws and install the slide and vertical power seat switch knob.

  38. INSTALL RECLINING POWER SEAT SWITCH KNOB


    1. A01NGTT

      Engage the 4 claws and install the reclining power seat switch knob.

  39. INSTALL FRONT SEAT INNER BELT ASSEMBLY


    1. A01NE9GE01
      Text in Illustration
      *1 Protruding Part

      Install the front seat inner belt assembly with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of front seat adjuster.

    2. Connect each connector and clamp.

  40. INSTALL POWER SEAT SLIDE MOTOR ASSEMBLY

    Tech Tips

    Perform this step only when replacing the power seat slide motor assembly.


    1. Install the power seat slide motor assembly Click here.