PRE-CRASH SAFETY SYSTEM Power Source Circuit

DESCRIPTION

This circuit supplies power to the seat belt control ECU.

WIRING DIAGRAM

A01NGA2E06

INSPECTION PROCEDURE

Note

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (PGND CIRCUIT)


    1. A01NEY1E01
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Seat Belt Control ECU)

      Disconnect the seat belt control ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F57-8 (PGND) - Body ground Always Below 1 Ω
    3. Reconnect the seat belt control ECU connector.


    NG
    OK
  2. CHECK HARNESS AND CONNECTOR (IG1 CIRCUIT)


    1. A01NDDZE01
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Seat Belt Control ECU)

      *2

      Front view of wire harness connector

      (to Seat Belt Control ECU)

      Disconnect the 2 seat belt control ECU connectors.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      F56-8 (IG1) - F57-8 (PGND) Power switch on (IG) 11 to 14 V
    4. Reconnect the 2 seat belt control ECU connectors.


    NG
    OK
  3. CHECK HARNESS AND CONNECTOR (+B CIRCUIT)


    1. A01NEY1E03
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Seat Belt Control ECU)

      Disconnect the seat belt control ECU connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      F57-7 (+B) - Body ground Always 11 to 14 V
    3. Reconnect the seat belt control ECU connector.


    NG
    OK
  4. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    1. Remove the instrument panel junction block assembly.

      A01NEWRE01
      Text in Illustration
      *1 Instrument Panel Junction Block Assembly
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2K-1 - 2D-30 Always 10 kΩ or higher
      2K-1 - 2D-30 When battery voltage applied to terminals 2A-20 and 2A-3 Below 1 Ω
    3. Reinstall the instrument panel junction block assembly.


    NG
    OK
  5. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - SEAT BELT CONTROL ECU)


    1. A01NGFTE01
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Seat Belt Control ECU)

      *2

      Front view of wire harness connector

      (to Instrument Panel Junction Block Assembly)

      Disconnect the instrument panel junction block assembly connector.

    2. Disconnect the seat belt control ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2D-30 - F56-8 (IG1) Always Below 1 Ω
      2D-30 - Body ground Always 10 kΩ or higher
      F56-8 (IG1) - Body ground Always 10 kΩ or higher
    4. Reconnect the seat belt control ECU connector.

    5. Reconnect the instrument panel junction block assembly connector.


    NG
    OK
  6. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - BODY GROUND)


    1. A01NHZ8E01
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Instrument Panel Junction Block Assembly)

      Disconnect the instrument panel junction block assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2A-3 - Body ground Always Below 1 Ω
    3. Reconnect the instrument panel junction block assembly connector.


    NG
    OK
  7. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - POWER MANAGEMENT ECU)


    1. A01NFUAE02
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Power Management Control ECU)

      *2

      Front view of wire harness connector

      (to Instrument Panel Junction Block Assembly)

      Disconnect the instrument panel junction block assembly connector.

    2. Disconnect the power management control ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2A-20 - F98-2 (IG1D) Always Below 1 Ω
      2A-20 - Body ground Always 10 kΩ or higher
      F98-2 (IG1D) - Body ground Always 10 kΩ or higher
    4. Reconnect the power management control ECU connector.

    5. Reconnect the instrument panel junction block assembly connector.


    NG
    OK