CENTER AIRBAG SENSOR ASSEMBLY INSTALLATION


  1. INSTALL CENTER AIRBAG SENSOR ASSEMBLY


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01ND7ZE02
      Text in Illustration
      *1 Fulcrum Length
      *2 Waterproof Sheet

      Using SST and a torque wrench, install the center airbag sensor assembly with the 3 bolts.

      SST
      09961-00950
      Torque:
      without SST
      18 N*m  { 178 kgf*cm, 13 ft.*lbf }
      with SST
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

      Note


      • Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).

      • This torque value is effective when SST is parallel to a torque wrench.

      • If the center airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.

      • When installing the center airbag sensor assembly, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

      • When the power switch is first turned on (IG) after the center airbag sensor assembly has been replaced, make sure that no one is in the vehicle.

    4. Connect the connector to the center airbag sensor assembly as shown in the illustration.

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.

    5. Check that the waterproof sheet is properly set.

    6. Check that there is no looseness in the installation parts of the center airbag sensor assembly.

  2. INSTALL CONSOLE BOX (for LHD)


    1. A01NF55E01
      Text in Illustration
      *1 Clamp
      *2 Guide

      Engage the 3 guides as shown in the illustration.

    2. Engage the 2 clamps.

    3. Install the 3 clips.

    4. A01NDJA

      Install the console box with the 5 screws <D>.

  3. INSTALL CONSOLE BOX (for RHD)


    1. A01NDV8E01
      Text in Illustration
      *1 Clamp
      *2 Guide

      Engage the 3 guides as shown in the illustration.

    2. Engage the 2 clamps.

    3. Install the 2 clips.

    4. A01NCM1

      Install the console box with the 5 screws <D>.

  4. INSTALL REAR CONSOLE BOX ASSEMBLY


    1. A01ND4Q

      Engage the 8 guides as shown in the illustration.

    2. A01NEDEE01
      Text in Illustration
      *1 Screw
      *2 Bolt

      Install the rear console box assembly with the 2 screws and 4 bolts.

    3. Connect each connector.

  5. INSTALL MULTI-MEDIA INTERFACE ECU ASSEMBLY (w/ USB Audio System)


    1. Connect the connector.

    2. A01NG12

      Engage the clip and guide.

    3. Install the multi-media interface ECU assembly with the 2 bolts.

      Torque:
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

  6. INSTALL CONSOLE REAR END PANEL SUB-ASSEMBLY


    1. A01NGOF

      w/o Rear Seat Entertainment System:


      1. Engage the 4 claws and 6 clips to install the console rear end panel sub-assembly.

    2. w/ Rear Seat Entertainment System:


      1. Connect each connector.

      2. Engage the 4 claws and 6 clips to install the console rear end panel sub-assembly.

  7. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL


    1. A01NF11

      Engage the 7 clips to install the lower instrument panel finish panel as shown in the illustration.

  8. INSTALL INSTRUMENT PANEL FINISH PANEL


    1. A01ND4S

      Engage the 2 guides, claw and 2 clips to install the instrument panel finish panel as shown in the illustration.

  9. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. Connect each connector.

    2. A01NG78

      Engage the 8 clips and 2 guides.

    3. Install the lower instrument panel finish panel sub-assembly with the 2 screws <D>.

    4. A01NE1K

      Engage the 2 claws to close the cover as shown in the illustration.

  10. INSTALL NO. 1 SWITCH HOLE BASE


    1. Connect each connector.

    2. A01NFF7

      Engage the 4 claws and 2 guides to install the No. 1 switch hole base.

  11. INSTALL INSTRUMENT PANEL GARNISH LH


    1. A01NH3A

      Engage the 6 clips to install the instrument panel garnish LH.

  12. INSTALL NO. 2 CONSOLE BOX DUCT


    1. A01NH7K

      Install the No. 2 console box duct with the 2 screws.

  13. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. Engage the clamp.

    2. Connect each connector.

    3. A01NEE4

      Engage the 3 claws and 3 clips.

    4. w/o Seat Heater System:


      1. Connect the connector to the console box hole cover.

    5. A01NDQX

      w/ Seat Heater System:


      1. Engage the 4 claws to install the seat heater switch assembly.

      2. Connect the connector.

    6. A01NHPA

      Engage the 4 claws and 4 clips to install the upper console panel sub-assembly.

  14. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A01NH7J

      Turn the shift lever knob sub-assembly clockwise to install the shift lever knob sub-assembly.

  15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  16. INSTALL REAR DECK FLOOR BOX


    1. A01NDSY

      Install the rear deck floor box with the 3 clips.

  17. PERFORM DIAGNOSTIC SYSTEM CHECK


    1. Perform a diagnostic system check Click here.

  18. INSPECT SRS WARNING LIGHT


    1. Inspect the SRS warning light Click here.

  19. INSPECT SUSPENSION CONTROL SYSTEM


    1. Inspect the suspension control system Click here.