FRONT SEAT SIDE AIRBAG ASSEMBLY DISPOSAL

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


  1. PRECAUTION

    CAUTION:


    • An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with your bare hands to discharge static electricity before performing this procedure.

    • Never dispose of a front seat side airbag assembly with an undeployed airbag.

    • The airbag produces an exploding sound when it is deployed, so perform the operation outdoors and where it will not create a nuisance to nearby residents.

    • When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool). Perform the operation in a place away from electrical noise.

    • When deploying the airbag, perform the operation at least 10 m (32.8 ft.) away from the front seat side airbag assembly.

    • The front seat side airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

    • Use gloves and safety glasses when handling a front seat side airbag assembly with a deployed airbag.

    • Do not apply water etc. to a front seat side airbag assembly with a deployed airbag.

    • Always wash your hands with water after completing the operation.

    Tech Tips

    When scrapping a vehicle equipped with an SRS or disposing of the front seat side airbag assembly, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the Service Dept. of the distributor.

  2. DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY (When Installed in Vehicle)

    Note


    • When disposing of the front seat side airbag assembly, never use the customer's vehicle to deploy the airbag.

    • Be sure to observe the following procedure when deploying the airbag.

    Tech Tips

    Prepare a battery as the power source to deploy the airbag.


    1. A01NDGCE06

      Check the function of SST Click here.

      SST
      09082-00700

    2. Refer to Precaution Click here.

    3. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    4. Disconnect the connector from the front seat side airbag assembly under the front seat assembly.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.


      1. Slide the slider to release the lock, and then disconnect the yellow airbag connector under the front seat assembly.

        A01NGRHE02
        Text in Illustration
        *1 Slider - -

    5. Install SST.

      CAUTION:

      Check that there is no looseness in the front seat assembly.


      1. A01NHEAE01

        Connect the SST connector to the front seat side airbag assembly connector.

        SST
        09082-00700
        09082-00820

        Note

        To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock.

      2. A01NF5RE02
        Text in Illustration
        *1 Battery

        Move SST at least 10 m (32.8 ft.) away from the front side window of the vehicle.

      3. Maintaining sufficient clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.

        Note

        Take care not to damage the SST wire harness.

      4. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

    6. Deploy the airbag.


      1. Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.

      2. Press the SST activation switch and deploy the airbag.

        CAUTION:


        • Before deployment, make sure that no one is near the vehicle.

        • The front seat side airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

        • Use gloves and safety glasses when handling a front seat side airbag assembly with a deployed airbag.

        • Do not apply water etc. to a front seat side airbag assembly with a deployed airbag.

        • Always wash your hands with water after completing the operation.

        Tech Tips

        The airbag is deployed as the LED of the SST activation switch comes on.

  3. DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY (When not Installed in Vehicle)

    Note

    Be sure to observe the following procedure when deploying the airbag.

    Tech Tips

    Prepare a battery as the power source to deploy the airbag.


    1. A01NDGCE06

      Check the function of SST Click here.

      SST
      09082-00700

    2. Remove the front seat side airbag assembly Click here.

      CAUTION:


      • Before removing the front seat assembly, wait at least 90 seconds after turning the power switch off and disconnecting the cable from the negative (-) battery terminal.

      • When storing the front seat side airbag assembly, keep the airbag deployment side facing upward.

    3. A01NDOVE18

      Using braided wire, tie down the front seat side airbag assembly to an unneeded tire.

      Text in Illustration
      *1 Stripped Wire Section
      *2 Wire Diameter
      Wire
      Stripped wire section
      1.25 mm2 (0.0019 in.2) or more

      CAUTION:

      If the wire is too thin or an alternative object is used to tie down the front seat side airbag assembly, it may snap when the airbag is deployed. Always use a wire for vehicle use with an area of at least 1.25 mm2(0.0019 in.2).

      Tech Tips

      To calculate the area of the stripped wire section:

      Area = 3.14 x (Diameter)2/ 4


      1. A01NET7

        Install the 2 nuts to the front seat side airbag assembly.

      2. A01NDYT

        Wind the wires around the stud bolts of the front seat side airbag assembly as shown in the illustration.

      3. A01NG8WE02
        Text in Illustration
        *1 Inner Diameter
        *2 Width

        Position the front seat side airbag assembly inside the tire.

        Minimum tire size
        Must exceed the following dimensions
        Width
        185 mm (7.28 in.)
        Inner diameter
        360 mm (1.18 ft.)

        CAUTION:


        • Make sure that the wires are tight. If there is slack in the wires, the front seat side airbag assembly may break loose when the airbag is deployed.

        • Face the front seat side airbag assembly deployment surface toward the inside the tire to evenly distribute the force of deployment.

        Note

        The tire may be marked by the airbag deployment, so use an unneeded tire.

    4. Install SST.


      1. A01NEUDE01

        Connect the SST connector to the front seat side airbag assembly connector.

        SST
        09082-00820
    5. A01NFVAE02

      Place the tires.


      1. Place at least 2 tires under the tire to which the front seat side airbag assembly is tied.

      2. Place at least 2 tires onto the tire to which the front seat side airbag assembly is tied. The top tire should have a wheel installed.

        Note

        Do not place the SST connector under the tire because it could be damaged.

      3. A01NCYM

        Tie the tires together with the 2 wires.

        CAUTION:

        Make sure that the wires are tight. Looseness in the wires results in the tires breaking loose when the airbag is deployed.

    6. Install SST.


      1. A01NCNCE24
        Text in Illustration
        *1 Front Seat Side Airbag Assembly
        *2 Battery

        Connect the SST connector.

        SST
        09082-00700

        Note

        To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the tire.

      2. Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the tire.

    7. Deploy the airbag.


      1. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

      2. Check that no one is within a 10 m (32.8 ft.) radius of the tire to which the front seat side airbag assembly is tied.

      3. Press the SST activation switch and deploy the airbag.

        CAUTION:

        Before deployment, make sure that no one is near the airbag.

        Tech Tips

        The airbag is deployed as the LED of the SST activation switch comes on.

    8. A01NCQ4

      Dispose of the front seat side airbag assembly.

      CAUTION:


      • The front seat side airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

      • Use gloves and safety glasses when handling a front seat side airbag assembly with a deployed airbag.

      • Do not apply water etc. to a front seat side airbag assembly with a deployed airbag.

      • Always wash your hands with water after completing the operation.


      1. Remove the front seat side airbag assembly from the tire.

      2. Place the front seat side airbag assembly in a plastic bag, tie it tightly, and dispose of it according to local regulations.