KNEE AIRBAG ASSEMBLY (for Driver Side) INSTALLATION


  1. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01NDDE

      Engage the claw to connect the hood lock control cable to the driver side knee airbag assembly.

    4. Connect the airbag connector to the driver side knee airbag assembly.

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.

    5. A01NHD8

      Temporarily install the driver side knee airbag assembly with the 2 claws and 2 hooks.

    6. Install the driver side knee airbag assembly with the 4 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note

      Confirm that the driver side knee airbag assembly is installed securely without any excessive gaps and is not protruding outward.

  2. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. Connect each connector.

    2. A01NG78

      Engage the 8 clips and 2 guides.

    3. Install the lower instrument panel finish panel sub-assembly with the 2 screws <D>.

    4. A01NE1K

      Engage the 2 claws to close the cover as shown in the illustration.

  3. INSTALL NO. 1 SWITCH HOLE BASE


    1. Connect each connector.

    2. A01NFF7

      Engage the 4 claws and 2 guides to install the No. 1 switch hole base.

  4. INSTALL INSTRUMENT PANEL GARNISH LH


    1. A01NH3A

      Engage the 6 clips to install the instrument panel garnish LH.

  5. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)


    1. Engage each clamp.

    2. Connect each connector.

    3. A01NCLN

      Engage the claw and 2 guides.

    4. A01NG9O

      Install the No. 1 instrument panel under cover sub- assembly with the 2 screws <D>.

  6. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)


    1. Engage each clamp.

    2. Connect each connector.

    3. A01NHAW

      Engage the claw and 2 guides.

    4. A01NF7E

      Install the No. 1 instrument panel under cover sub- assembly with the 2 screws <D>.

  7. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A01NFZB

      Engage the 2 clips to install the cowl side trim sub-assembly LH.

    2. Install the clip.

  8. INSTALL FRONT DOOR SCUFF PLATE LH


    1. w/ Illumination:


      1. Connect the connector.

    2. A01NHW7

      Engage the 4 clips, guide and 7 claws, and install the front door scuff plate LH.

  9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  10. INSTALL REAR DECK FLOOR BOX


    1. A01NDSY

      Install the rear deck floor box with the 3 clips.

  11. PERFORM DIAGNOSTIC SYSTEM CHECK


    1. Perform a diagnostic system check Click here.

  12. INSPECT SRS WARNING LIGHT


    1. Inspect the SRS warning light Click here.

  13. INSPECT SUSPENSION CONTROL SYSTEM


    1. Inspect the suspension control system Click here.