SECURITY HORN ASSEMBLY (for Built-in Battery type) REMOVAL


  1. PRECAUTION (w/ Navigation System for HDD)

    Note

    After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

    Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal
    Specification Waiting Time
    w/o Telematics transceiver 60 sec.
    w/ Telematics transceiver 120 sec.

  2. REMOVE REAR DECK FLOOR BOX


    1. A01NDSY

      Remove the 3 clips and the rear deck floor box.

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE REAR SEAT HEADREST ASSEMBLY RH


    1. A01NGCA

      Press the headrest support button and pull up the headrest as shown in the illustration.

  5. REMOVE REAR SEAT CENTER HEADREST ASSEMBLY


    1. A01NHYA

      Press the headrest support button and pull up the headrest as shown in the illustration.

  6. REMOVE REAR SEAT OUTER TRACK BRACKET COVER RH


    1. A01NHX5

      Disengage the 4 claws and remove the rear seat track bracket cover RH.

  7. REMOVE REAR SEAT INNER TRACK BRACKET COVER RH


    1. A01NGSN

      Disengage the 4 claws and remove the 4 rear seat track bracket cover RH.

  8. DISCONNECT REAR SEAT LOCK CABLE ASSEMBLY RH


    1. A01NGJL

      Using a clip remover, remove the 2 clips and disconnect the rear seatback board sub-assembly.

    2. A01NEKF

      Using a clip remover, remove the 3 clips and disconnect the rear seatback board carpet assembly RH.

    3. A01NGPZ

      Remove the bolt.

    4. Disengage the guide and disconnect the No. 1 fold seat stopper band assembly.

    5. Pull down the adjusters lock piece to release the lock as shown in the illustration.

      A01NHFNE01
      Text in Illustration
      *1 Adjusters Spring *2 Lock Piece
    6. A01NE3UE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver wrapped with protective tape, disconnect the No. 1 reclining control cable as shown in the illustration.

    7. A01NHZA

      Remove the rear seat reclining control cable from the cover as shown in the illustration.

    8. Lift up the seat track adjusting handle to the uppermost position and hold the handle in this position as shown in the illustration.

      A01NFIEE01
      Text in Illustration
      *1 Seat Track Adjusting Handle *2 Protective Tape

    9. Using a screwdriver wrapped with protective tape, disconnect the No. 1 rear seat lock cable assembly as shown in the illustration.

    10. Using a screwdriver wrapped with protective tape, disconnect the rear seat lock cable assembly RH as shown in the illustration.

      A01NECJE01
      Text in Illustration
      *1 Protective Tape

    11. When replacing the rear seat assembly RH or rear seat reclining control cable with a new one:


      1. A01NEP9E01

        Cut portion A shown in the illustration to separate the rear seat assembly RH or rear seat reclining control cable.

    12. When replacing the rear seat lock cable assembly RH with a new one:


      1. A01NDEKE01

        Cut portion A shown in the illustration to separate the rear seat lock assembly RH.

  9. REMOVE REAR SEAT ASSEMBLY RH


    1. A01NCPO

      Disconnect the connector.

    2. A01NEWM

      Remove the 3 bolts on the rear side of the seat.

    3. A01NH4O

      Remove the 2 bolts on the front side of the seat and the rear seat assembly RH.

      Note

      Be careful not to damage the vehicle body.

  10. REMOVE DECK BOARD SUB-ASSEMBLY


    1. A01NFKA

      Disengage the 3 fasteners as shown in the illustration.

    2. for Compact Spare Tire:


      1. A01NGS3

        Remove the 2 bolts and remove the deck board sub-assembly.

    3. for Full Size Spare Tire:


      1. A01NEZN

        Remove the 2 bolts and remove the deck board sub-assembly.

  11. REMOVE SPARE WHEEL COVER ASSEMBLY (for Compact Spare Tire)


    1. Remove the spare wheel cover assembly.

  12. REMOVE TONNEAU COVER ASSEMBLY


    1. Remove the tonneau cover assembly.

  13. REMOVE NO. 3 REAR FLOOR BOARD (for Compact Spare Tire)


    1. A01NFBL

      Disengage the 2 guides and remove the No. 3 rear floor board.

  14. REMOVE NO. 3 REAR FLOOR BOARD (for Full Size Spare Tire)


    1. A01ND35

      Disengage the 2 guides and remove the No. 3 rear floor board.

  15. REMOVE DECK SIDE TRIM BOX RH (for Compact Spare Tire)


    1. A01NHZ2

      Remove the 2 clips and deck side trim box RH.

  16. REMOVE DECK SIDE TRIM BOX RH (for Full Size Spare Tire)


    1. A01NE2M

      Remove the 3 clips and the deck side trim box RH.

  17. REMOVE REAR FLOOR FINISH PLATE


    1. A01NCOE

      Disengage the 2 claws, 6 clips and 2 guides, and remove the rear floor finish plate.

  18. REMOVE REAR FLOOR FINISH SIDE PLATE RH

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  19. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  20. REMOVE REAR SEAT SIDE COVER RH

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  21. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  22. REMOVE ROPE HOOK ASSEMBLY

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  23. REMOVE RECLINING REMOTE CONTROL BEZEL RH

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  24. REMOVE HEIGHT CONTROL SWITCH (w/ Air Suspension)


    1. A01NH52

      Disengage the 2 claws to remove the height control switch from the deck trim side panel assembly RH.

    2. Disconnect the connector.

  25. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH


    1. Remove the 2 screws.

    2. Remove the 5 clips.

    3. Disengage the 5 claws and 2 clips.

    4. Disconnect the connector and remove the deck trim side panel assembly RH.

      A01NFKB

  26. REMOVE THEFT WARNING SIREN ASSEMBLY


    1. A01NGKA

      Remove the 2 nuts.

    2. Disconnect the connector and remove the theft warning siren assembly.