ELECTRICAL KEY OSCILLATOR (for Front Floor) REMOVAL


  1. PRECAUTION (w/ Navigation System for HDD)

    Note

    After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

    Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal
    Specification Waiting Time
    w/o Telematics transceiver 60 sec.
    w/ Telematics transceiver 120 sec.

  2. REMOVE REAR DECK FLOOR BOX (w/ Air Suspension)


    1. A01NDSY

      Remove the 3 clips and the rear deck floor box.

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Air Suspension)

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE REAR CONSOLE BOX ASSEMBLY

    Click here

  5. REMOVE INSTRUMENT PANEL GARNISH LH


    1. A01NGMK

      Using moulding remover B, disengage the 6 clips and remove the instrument panel garnish LH as shown in the illustration.

  6. REMOVE NO. 1 SWITCH HOLE BASE


    1. A01NFNE

      Push the No. 1 switch hole base in the direction indicated by the arrow to disengage the 4 claws and 2 guides.

    2. Disconnect each connector and remove the No. 1 switch hole base.

  7. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. A01NGE1

      Disengage the 2 claws and open the cover as shown in the illustration.

    2. A01NG78

      Remove the 2 screws <D>.

    3. Disengage the 8 clips and 2 guides.

    4. Disconnect each connector and remove the lower instrument panel finish panel sub-assembly.

  8. REMOVE INSTRUMENT PANEL FINISH PANEL


    1. A01NG2R

      Pull the instrument panel finish panel in the direction indicated by the arrow to disengage the claw, 2 clips and 2 guides, and remove the instrument panel finish panel.

  9. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL


    1. A01NHYG

      Pull the lower instrument panel finish panel in the direction indicated by the arrow to disengage the 7 clips and remove the lower instrument panel finish panel.

  10. REMOVE FRONT CONSOLE BOX COVER


    1. A01NEHJ

      Using moulding remover A, disengage the 2 clips and 5 guides.

    2. Disconnect the connector and remove the front console box cover.

  11. REMOVE CONSOLE BOX (for LHD)


    1. A01NDJA

      Remove the 5 screws <D>.

    2. A01NHTTE01
      Text in Illustration
      *1 Clamp
      *2 Guide

      Disengage the 2 clamps.

    3. Remove the 3 clips.

    4. Disengage the 3 guides and remove the console box as shown in the illustration.

  12. REMOVE CONSOLE BOX (for RHD)


    1. A01NCM1

      Remove the 5 screws <D>.

    2. A01NCP7E01
      Text in Illustration
      *1 Clamp
      *2 Guide

      Disengage the 2 clamps.

    3. Remove the 2 clips.

    4. Disengage the 3 guides and remove the console box as shown in the illustration.

  13. REMOVE ELECTRICAL KEY OSCILLATOR


    1. A01NDRR

      Disconnect the connector.

    2. Disengage the clamp and remove the electrical key oscillator.

      Note

      Be careful when removing the electrical key oscillator. If the oscillator is dropped, replace it with a new one.