ENTRY AND START SYSTEM (for Start Function), Diagnostic DTC:B2283

DTC Code DTC Name
B2283 Vehicle Speed Sensor Malfunction

DESCRIPTION

The skid control ECU converts wheel speed sensor signals into 4-pulse signals and sends them to the combination meter. After this signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter, it is then transmitted to the power management control ECU. The power management control ECU determines the vehicle speed based on the frequency of these pulse signals.

DTC No. DTC Detection Condition Trouble Area
B2283

Both conditions are met:


  • Over-deceleration in vehicle speed


  • Vehicle speed and engine speed do not match

  • AM2 fuse

  • Combination meter assembly

  • Power management control ECU

  • Wire harness or connector

WIRING DIAGRAM

A01NHGFE08

INSPECTION PROCEDURE

Note


  • When the power management control ECU is replaced with a new one and the cable from the negative (-) auxiliary battery terminal is connected, the power source mode becomes on (IG) mode. When the auxiliary battery is removed and reinstalled, the power source mode that was selected when the auxiliary battery was removed is restored.

  • Inspect the fuse for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. CHECK CAN COMMUNICATION SYSTEM


    1. Check if CAN communication DTCs are output.

      Tech Tips

      If any DTCs for CAN communication system malfunction are output, inspect those DTCs first.

      OK
      CAN communication DTC is not output.

    NG

    GO TO CAN COMMUNICATION SYSTEM (DIAGNOSTIC TROUBLE CODE CHART) Click here

    OK

  2. CHECK SPEEDOMETER OPERATION


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Combination Meter / Data List.

    5. Check the Data List for proper functioning of the vehicle speed signal.

      Combination Meter
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Vehicle Speed Meter Vehicle speed/Min.: 0, Max.: 255 Almost same as actual speed (When driving) -
      OK
      Vehicle speed displayed on the intelligent tester is almost the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).

    NG

    GO TO METER / GAUGE SYSTEM (Speedometer Malfunction) Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - POWER MANAGEMENT CONTROL ECU)


    1. A01NHLTE03
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Power Management Control ECU)
      *2

      Front view of wire harness connector

      (to Power Management Control ECU)

      Disconnect the F97 and F98 connectors from the power management control ECU.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      F97-1 (AM22) - Body ground Always 9.5 to 16 V
      F98-7 (AM21) - Body ground Always 9.5 to 16 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (AUXILIARY BATTERY - POWER MANAGEMENT CONTROL ECU)

    OK

  4. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)


    1. A01NHLTE04
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Power Management Control ECU)
      *2

      Front view of wire harness connector

      (to Power Management Control ECU)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F97-5 (E01) - Body ground Always Below 1 Ω
      F97-6 (E1) - Body ground Always Below 1 Ω
      F98-4 (E12) - Body ground Always Below 1 Ω
      F98-5 (E02) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)

    OK

  5. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - POWER MANAGEMENT CONTROL ECU)


    1. A01NH28E02
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Power Management Control ECU)
      *2

      Front view of wire harness connector

      (to Combination Meter Assembly)

      Disconnect the F15 connector from the combination meter assembly.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F97-14 (SPDI) - F15-3 (+S) Always Below 1 Ω
      F97-14 (SPDI) - Body ground Always 10 kΩ or higher

    NG

    Click here

    OK

  6. READ VALUE USING INTELLIGENT TESTER


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Power Source Control / Data List.

    5. Read the Data List according to the display on the intelligent tester.

      Power Source Control
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Vehicle Speed Signal Vehicle speed signal/Stop or Run

      Stop: Vehicle stopped

      Run: Vehicle running

      		 -
      OK
      Stop (vehicle is stopped) and Run (vehicle is running) appear on the screen.

    NG

    GO TO METER / GAUGE SYSTEM (Speedometer Malfunction) Click here

    OK

  7. CHECK SPEED SIGNAL INPUT STATUS


    1. A01NCPVE29
      Text in Illustration
      *1

      Component with harness connected

      (Combination Meter Assembly)

      Remove the combination meter Click here.

    2. Reconnect the F15 connector to the combination meter assembly.

    3. Reconnect the F8 connector to the power management control ECU.

    4. Connect an oscilloscope to terminal F15-3 (+S) and body ground.

    5. Turn the power switch on (IG).

    6. Turn the wheel slowly.

    7. Check the signal waveform according to the condition(s) in the table below.

      Item Condition
      Tool setting 5 V/DIV., 20 ms./DIV.
      Vehicle condition Driving at approx. 20 km/h (12 mph)
      Result
      Result Proceed to
      The waveform is displayed as shown in the illustration (for LHD). A
      The waveform is displayed as shown in the illustration (for RHD). B
      The waveform is not displayed as shown in the illustration. C

      Tech Tips

      When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.


    B

    REPLACE POWER MANAGEMENT CONTROL ECU (for RHD) Click here

    C

    GO TO METER / GAUGE SYSTEM (Speed Signal Circuit) Click here

    A

    REPLACE POWER MANAGEMENT CONTROL ECU (for LHD) Click here

  8. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - JUNCTION BLOCK)


    1. Disconnect the F93 connector.

      A01NDIXE02

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F15-3 (+S) - F93-57 Always Below 1 Ω
      F15-3 (+S) - Body ground Always 10 kΩ or higher
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Junction Block)

      		 *2

      Front view of wire harness connector

      (to Combination Meter Assembly)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER - JUNCTION BLOCK)

    OK

  9. CHECK HARNESS AND CONNECTOR (JUNCTION BLOCK - POWER MANAGEMENT CONTROL ECU)


    1. Measure the resistance according to the value(s) in the table below.

      A01ND48E03
      Standard Resistance
      Tester Connection Condition Specified Condition
      F97-14 (SPDI) - F93-37 Always Below 1 Ω
      F97-14 (SPDI) - Body ground Always 10 kΩ or higher
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Junction Block)

      		 *2

      Front view of wire harness connector

      (to Power Management Control ECU)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (JUNCTION BLOCK - POWER MANAGEMENT CONTROL ECU)

    OK

    REPLACE JUNCTION BLOCK