ENTRY AND START SYSTEM (for Entry Function) Back Door Entry Lock Function does not Operate

DESCRIPTION

If the back door entry lock function does not operate but the back door open function operates, the communication between the vehicle and key is normal. As a faulty part, the entry lock switch circuit (from the back door opener switch assembly (lock switch) to the certification ECU (smart key ECU assembly)) is suspected.

WIRING DIAGRAM

A01NDJFE05

INSPECTION PROCEDURE

Note


  • The entry and start system (for entry function) uses a multiplex communication system (LIN communication system) and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting Click here. Troubleshoot the entry and start system (for entry function) after confirming that the communication system is functioning properly.

  • Confirm that another key is not in the cabin.

PROCEDURE


  1. CHECK POWER DOOR LOCK OPERATION


    1. When the door control switch on the master switch assembly is operated, check that the doors unlock and lock according to switch operation Click here.

      OK
      Door locks operate normally.

    NG

    GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Problem Symptoms Table) Click here

    OK

  2. READ VALUE USING INTELLIGENT TESTER (BACK DOOR OPENER SWITCH)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Entry & Start / Data List.

    5. Read the Data List according to the display on the intelligent tester.

      Entry & Start (Certification ECU (Smart Key ECU Assembly))
      Tester Display Measurement Item/Display Normal Condition Diagnostic Note
      Tr/B-Door Lock SW Back door opener switch assembly (lock switch) / ON or OFF

      ON: Back door opener switch assembly (lock switch) pushed

      OFF: Back door opener switch assembly (lock switch) not pushed

      		 -
      OK
      On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.

    NG

    INSPECT BACK DOOR OPENER SWITCH ASSEMBLY Click here

    OK

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

  3. INSPECT BACK DOOR OPENER SWITCH ASSEMBLY


    1. A01NGD5E01
      Text in Illustration
      *1

      Component without harness connected

      (Back Door Opener Switch Assembly)

      Remove the back door opener switch assembly Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Position Specified Condition
      1 (L) - 2 (E) Back door opener switch assembly (lock switch) not pushed (OFF) 10 kΩ or higher
      1 (L) - 2 (E) Back door opener switch assembly (lock switch) pushed (ON) Below 1 Ω

    NG

    REPLACE BACK DOOR OPENER SWITCH ASSEMBLY Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - BACK DOOR OPENER SWITCH)


    1. A01NDSAE04
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Certification ECU (Smart Key ECU Assembly))
      *2

      Front view of wire harness connector

      (to Back Door Opener Switch Assembly)

      Disconnect the certification ECU (smart key ECU assembly) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F58-23 (TSW6) - Y11-1 (L) Always Below 1 Ω
      F58-23 (TSW6) - Body ground Always 10 kΩ or higher
      Y11-1 (L) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)