ENTRY AND START SYSTEM (for Entry Function) Driver Side Door Entry Lock and Unlock Functions do not Operate

DESCRIPTION

When the entry lock and unlock functions do not operate only for the driver door, an error in output request codes from the driver door or malfunction in the front door outside handle assembly is suspected. If the entry functions for the other doors operate normally, then the communication circuit between the key and door control receiver assembly is functioning normally. In this case, radio wave interference or a malfunction in the request code sending circuit (from the certification ECU (smart key ECU assembly) to the front door outside handle assembly (for driver side)) is suspected.

WIRING DIAGRAM

A01NDUJE06

INSPECTION PROCEDURE

Note


  • The entry and start system (for entry function) uses a multiplex communication system (LIN communication system) and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting Click here. Troubleshoot the entry and start system (for entry function) after confirming that the communication system is functioning properly.

  • Confirm that another key is not in the cabin.

PROCEDURE


  1. CHECK POWER DOOR LOCK OPERATION


    1. When the door control switch on the master switch assembly is operated, check that the doors unlock and lock according to switch operation Click here.

      OK
      Door locks operate normally.

    NG
    OK
  2. CHECK WAVE ENVIRONMENT


    1. A01NFEYE02

      Bring the key near the front door outside handle assembly (for driver side), and perform a driver door entry lock and unlock operation check.

      Note

      If the key is brought within 0.2 m (0.656 ft.) of the door outside handle assembly, communication is not possible.

      Tech Tips


      • When pressing the lock switch and touching the touch sensor, hold the electrical key transmitter about 1 m (3.28 ft.) above the ground and about 0.3 m (0.984 ft.) away from the vehicle as shown in the illustration.

      • When the key is brought near the front door outside handle assembly (for driver side), the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

      • If the operation is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

      OK
      Entry functions operate normally.

    NG
    OK
  3. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - FRONT DOOR OUTSIDE HANDLE)


    1. Disconnect the certification ECU (smart key ECU assembly) connector.

    2. A01NHLAE21
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Certification ECU (Smart Key ECU Assembly))

      *2

      Front view of wire harness connector

      (to Front Door Outside Handle Assembly (for Driver Side))

      *3 for LHD
      *4 for RHD

      Disconnect the front door outside handle assembly (for driver side) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      F58-3 (CLG1) - N1-6 (ANT1) Always Below 1 Ω
      F58-4 (CG1B) - N1-3 (ANT2) Always Below 1 Ω
      F58-32 (POS1) - N1-5 (B) Always Below 1 Ω
      F58-3 (CLG1) - Body ground Always 10 kΩ or higher
      F58-4 (CG1B) - Body ground Always 10 kΩ or higher
      F58-32 (POS1) - Body ground Always 10 kΩ or higher
      N1-6 (ANT1) - Body ground Always 10 kΩ or higher
      N1-3 (ANT2) - Body ground Always 10 kΩ or higher
      N1-5 (B) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      F58-3 (CLG1) - M1-6 (ANT1) Always Below 1 Ω
      F58-4 (CG1B) - M1-3 (ANT2) Always Below 1 Ω
      F58-32 (POS1) - M1-5 (B) Always Below 1 Ω
      F58-3 (CLG1) - Body ground Always 10 kΩ or higher
      F58-4 (CG1B) - Body ground Always 10 kΩ or higher
      F58-32 (POS1) - Body ground Always 10 kΩ or higher
      M1-6 (ANT1) - Body ground Always 10 kΩ or higher
      M1-3 (ANT2) - Body ground Always 10 kΩ or higher
      M1-5 (B) - Body ground Always 10 kΩ or higher

    NG
    OK
  4. CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - BODY GROUND)


    1. A01NFOYE19
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Front Door Outside Handle Assembly (for Driver Side))

      *2 for LHD
      *3 for RHD

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      N1-2 (GND) - Body ground Always Below 1 Ω
      for RHD
      Tester Connection Condition Specified Condition
      M1-2 (GND) - Body ground Always Below 1 Ω

    NG
    OK
  5. INSPECT FRONT DOOR OUTSIDE HANDLE ASSEMBLY (DOOR OSCILLATOR, LOCK/UNLOCK SENSOR SIGNAL INPUT)


    1. Reconnect the certification ECU (smart key ECU assembly) connector.

    2. A01NFOYE20
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Front Door Outside Handle Assembly (for Driver Side))

      *2 for LHD
      *3 for RHD

      Measure the voltage and check for pulses according to the value(s) in the table below.

      Standard
      for LHD
      Tester Connection Condition Specified Condition
      N1-6 (ANT1) - N1-3 (ANT2)
      • Power switch off

      • All doors closed

      • Key not in cabin

      No pulse generation
      N1-6 (ANT1) - N1-3 (ANT2)
      • Power switch off

      • All doors closed

      • Key not in cabin

      • All doors locked by wireless lock function

      Pulse generation
      N1-5 (B) - N1-2 (GND) Power switch off 9 to 14 V
      N1-5 (B) - N1-2 (GND) Power switch on (IG) Below 2 V
      for RHD
      Tester Connection Condition Specified Condition
      M1-6 (ANT1) - M1-3 (ANT2)
      • Power switch off

      • All doors closed

      • Key not in cabin

      No pulse generation
      M1-6 (ANT1) - M1-3 (ANT2)
      • Power switch off

      • All doors closed

      • Key not in cabin

      • All doors locked by wireless lock function

      Pulse generation
      M1-5 (B) - M1-2 (GND) Power switch off 9 to 14 V
      M1-5 (B) - M1-2 (GND) Power switch on (IG) Below 2 V

    NG
    OK
  6. REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Driver Side)


    1. Replace the front door outside handle assembly (for driver side) Click here.


    NEXT
  7. CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Driver Side)


    1. Check that the entry functions operate normally Click here.

      OK
      Entry functions operate normally.

    NG
    OK