ENTRY AND START SYSTEM (for Entry Function), Diagnostic DTC:B27A1

DTC Code DTC Name
B27A1 Open in Driver Side Electrical Antenna Circuit

DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and sends it to the electrical key oscillator built into the front door outside handle assembly (for driver side) at 0.25-second intervals. To detect a key near the driver door, the front door outside handle assembly (for driver side) creates a detection area with a radius of approximately 1.0 m (3.28 ft.) from the driver door at 0.25-second intervals.

DTC B27A1 is detected by the certification ECU (smart key ECU assembly) if an open circuit is detected between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver side) terminals (between CLG1 and ANT1, or CG1B and ANT2).

DTC No. DTC Detection Condition Trouble Area
B27A1 Open circuit detected between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver side) terminals (between CLG1 and ANT1, or CG1B and ANT2).

  • Front door outside handle assembly (for driver side)

  • Certification ECU (smart key ECU assembly)

  • Wire harness or connector

WIRING DIAGRAM

A01NF2WE05

INSPECTION PROCEDURE

Note

The entry and start system (for entry function) uses a multiplex communication system (LIN communication system) and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting Click here. Troubleshoot the entry and start system (for entry function) after confirming that the communication system is functioning properly.

PROCEDURE


  1. CHECK CONNECTOR (CONNECTOR CONNECTION CONDITION)


    1. Turn the power switch off.

    2. Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and the front door outside handle assembly (for driver side).

      OK
      Connectors are properly connected.

    NG

    CONNECT CONNECTORS PROPERLY

    OK

  2. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - FRONT DOOR OUTSIDE HANDLE)


    1. Disconnect the certification ECU (smart key ECU assembly) connector.

    2. A01NHLAE17
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Certification ECU (Smart Key ECU Assembly))
      *2

      Front view of wire harness connector

      (to Front Door Outside Handle Assembly (for Driver Side))
      *3 for LHD
      *4 for RHD

      Disconnect the front door outside handle assembly (for driver side) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      F58-3 (CLG1) - N1-6 (ANT1) Always Below 1 Ω
      F58-4 (CG1B) - N1-3 (ANT2) Always Below 1 Ω
      F58-3 (CLG1) - Body ground Always 10 kΩ or higher
      F58-4 (CG1B) - Body ground Always 10 kΩ or higher
      N1-6 (ANT1) - Body ground Always 10 kΩ or higher
      N1-3 (ANT2) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      F58-3 (CLG1) - M1-6 (ANT1) Always Below 1 Ω
      F58-4 (CG1B) - M1-3 (ANT2) Always Below 1 Ω
      F58-3 (CLG1) - Body ground Always 10 kΩ or higher
      F58-4 (CG1B) - Body ground Always 10 kΩ or higher
      M1-6 (ANT1) - Body ground Always 10 kΩ or higher
      M1-3 (ANT2) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - BODY GROUND)


    1. A01NFOYE17
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Front Door Outside Handle Assembly (for Driver Side))
      *2 for LHD
      *3 for RHD

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      N1-2 (GND) - Body ground Always Below 1 Ω
      for RHD
      Tester Connection Condition Specified Condition
      M1-2 (GND) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (INDOOR ELECTRICAL KEY OSCILLATOR SIGNAL OUTPUT)


    1. A01NH8NE08
      Text in Illustration
      *1

      Component with harness connected

      (Certification ECU (Smart Key ECU Assembly))

      Reconnect the certification ECU (smart key ECU assembly) connector.

    2. Measure the resistance and check for pulses according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F58-15 (E) - Body ground Always Below 1 Ω
      Standard
      Tester Connection Condition Specified Condition
      F58-3 (CLG1) - F58-15 (E)

      • Power switch off

      • All doors closed

      • Key not in cabin

      		 No pulse generation
      F58-3 (CLG1) - F58-15 (E)

      • Power switch off

      • All doors closed

      • Key not in cabin

      • All doors locked by wireless lock function

      		 Pulse generation
      F58-4 (CG1B) - F58-15 (E)

      • Power switch off

      • All doors closed

      • Key not in cabin

      		 No pulse generation
      F58-4 (CG1B) - F58-15 (E)

      • Power switch off

      • All doors closed

      • Key not in cabin

      • All doors locked by wireless lock function

      		 Pulse generation

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    OK

  5. REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Driver Side)


    1. Replace the front door outside handle assembly (for driver side) Click here.


    NEXT

  6. CHECK DTC OUTPUT


    1. Clear the DTCs Click here.

    2. Recheck for DTCs.

      OK
      DTC B27A1 is not output.

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    OK

    END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY WAS DEFECTIVE)