ENTRY AND START SYSTEM (for Entry Function) CUSTOMIZE PARAMETERS


  1. CUSTOMIZING FUNCTION WITH INTELLIGENT TESTER

    Tech Tips

    The items in the table below can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Be sure to make a note of the current setting before customizing.

    • When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Customize Setting / Entry & Start or Warning.

    5. Select the setting by referring to the table below.

      Entry & Start
      Tester Display Default Content Setting
      Ignition Available Area All Function that switches the entry hybrid vehicle control system start detection area Front or All
      Park Wait Time 2.5 s Function that sets waiting time to permit opening door after door is locked with entry lock function 0.5 s, 1.5 s, 2.5 s, or 5 s
      Back Door Opening Operation Long Function that opens the back door when the driver has the key and presses back door opener switch assembly (opener switch) Long, Twice or OFF
      Warning
      Tester Display Default Content Setting
      Key Low Battery Warning ON Function that warns driver that key battery is weak ON or OFF

  2. ENTRY UNLOCK MODE SWITCHING

    Note

    Because the key (for card type) does not have a wireless transmitter function, it cannot be used to change the entry unlock mode.


    1. To change the vehicle entry unlock mode, make sure that the vehicle power is off and simultaneously push and hold the key lock switch and another key switch for 5 seconds.

      When the switches are pressed and held for 5 seconds, the entry door unlock mode changes to the mode that is not currently selected.

      Note

      After pressing and holding the switches for 5 seconds, wait 5 seconds before performing the same procedure again.


      • Driver door unlock mode:

        When the driver door touch sensor is touched, only the driver door unlocks. When another touch sensor is touched, all doors unlock.

      • All door unlock mode:

        When any touch sensor is touched, all doors unlock.

    2. The certification ECU (smart key ECU assembly) receives this signal from the door control receiver assembly and changes the entry and start system to the entry unlock mode.

    3. The certification ECU (smart key ECU assembly) sounds the buzzers of the wireless door lock buzzer assembly and combination meter assembly (buzzer) to inform the user that the mode has been changed.


      1. for Australia and New Zealand

        Mode Wireless Door Lock Buzzer Assembly Combination Meter Assembly (Buzzer)

        Driver Door

        (Default)

        		 Sounds 3 times Sounds once

        All Doors

        (Customized)

        		 Sounds 2 times Sounds once

        Tech Tips

        The procedure only changes the entry unlock mode of the entry and start system. It does not switch the unlocking of the wireless door lock control.

      2. for except Australia and New Zealand

        Mode Wireless Door Lock Buzzer Assembly Combination Meter Assembly (Buzzer)

        Driver Door

        (Customized)

        		 Sounds 3 times Sounds once

        All Doors

        (Default)

        		 Sounds 2 times Sounds once

        Tech Tips

        The procedure only changes the entry unlock mode of the entry and start system. It does not switch the unlocking of the wireless door lock control.

  3. ELECTRICAL KEY CANCEL

    Note

    Because the key (for card type) does not have a wireless transmitter function, it cannot be used to perform the key cancel operation.

    The electrical key cancel operation disables the following functions:


    • Entry Unlock/Lock

    • Entry Hybrid Vehicle Control System Start

    • Entry Back Door Open

    • Electrical Key Lock-in Prevention

    • Warning

    • Memory Call


    1. The operation procedures are as follows:

      Precondition:

      Power switch off, driver side door closed and unlocked.


      1. Push the unlock switch of the key once.

      2. Open the driver door within 5 seconds.

      3. Push the unlock switch of the key twice within 5 seconds.

      4. Close and open the driver door twice within 30 seconds.

        (Driver door: Close → Open → Close → Open)

      5. Push the unlock switch of the key twice within 5 seconds.

      6. Close and open the driver door within 30 seconds.

        (Driver door: Close → Open)

      7. Close the driver door within 5 seconds.

        When electrical key cancel is activated, the wireless door lock buzzer sounds twice.

        To return to the original condition, perform the procedures again. When the original condition is returned, the wireless door lock buzzer sounds once.