DOOR CONTROL RELAY INSTALLATION


  1. INSTALL DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY


    1. A01NE3O

      Install the double lock door control relay assembly with the 2 bolts.

    2. A01NG2G

      Connect the connector.

  2. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


    1. Connect each connector.

    2. A01NGIS

      Engage the claw, 4 clips and guide.

    3. A01NFHC

      Install the glove compartment door assembly with the 5 screws <F>.

  3. INSTALL PASSENGER SIDE KNEE AIRBAG ASSEMBLY


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01NHUG

      Connect the airbag connector to the front passenger side knee airbag assembly.

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.

    4. A01NFZX

      Temporarily install the front passenger side knee airbag assembly with the claw and 2 pins.

    5. Install the front passenger side knee airbag assembly with the 3 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note

      Confirm that the front passenger side knee airbag assembly is installed securely without any excessive gaps and is not protruding outward.

    6. A01NFX4E01
      Text in Illustration
      *1 Protective Tape

      Remove the protective tape.

  4. INSTALL INSTRUMENT PANEL GARNISH RH (w/o Airbag Cut Off Switch)

    Tech Tips

    Removal procedure of the RH side is the same as that of the LH side Click here.

  5. INSTALL INSTRUMENT PANEL GARNISH RH (w/ Airbag Cut Off Switch)


    1. Connect the connector.

    2. A01NGEE

      Engage the 6 clips to install the instrument panel garnish RH.

  6. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. Connect the connector.

    2. A01NH29

      Engage the 2 guides and 4 claw to install the No. 2 instrument panel under cover sub-assembly.

  7. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Removal procedure of the RH side is the same as that of the LH side Click here.

  8. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Removal procedure of the RH side is the same as that of the LH side Click here.

  9. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL


    1. A01NF11

      Engage the 7 clips to install the lower instrument panel finish panel as shown in the illustration.

  10. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. Engage the clamp.

    2. Connect each connector.

    3. A01NEE4

      Engage the 3 claws and 3 clips.

    4. w/o Seat Heater System:


      1. Connect the connector to the console box hole cover.

    5. A01NDQX

      w/ Seat Heater System:


      1. Connect the connector.

      2. Engage the 4 claws to install the seat heater switch assembly.

    6. A01NHPA

      Engage the 4 claws and 4 clips to install the upper console panel sub-assembly.

  11. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A01NH7J

      Turn the shift lever knob sub-assembly clockwise to install the shift lever knob sub-assembly.

  12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  13. INSTALL REAR DECK FLOOR BOX


    1. A01NDSY

      Install the rear deck floor box with the 3 clips.