BACK DOOR LOCK REMOVAL


  1. REMOVE TONNEAU COVER SUB-ASSEMBLY

  2. REMOVE BACK DOOR FINISH COVER LH (w/o Power Back Door)


    1. A01NDR0

      Using a moulding remover, disengage the 6 claws and remove the back door finish cover LH.

  3. REMOVE BACK DOOR TRIM BASE (w/ Power Back Door)


    1. A01NDBV

      Using a moulding remover, disengage the 4 claws and remove the back door trim base.

  4. REMOVE BACK DOOR FINISH COVER RH (w/o Power Back Door)


    1. A01NF4F

      Using a moulding remover, disengage the 6 claws and remove the back door finish cover RH.

  5. REMOVE DOOR PULL HANDLE WITH SWITCH (w/ Power Back Door)


    1. A01NEX4

      Using a moulding remover, disengage the 6 claws and remove the door pull handle with switch.

    2. Disconnect the connector.

  6. REMOVE BACK DOOR LOCK COVER


    1. A01NDAS

      Disengage the 4 claws and remove the back door lock cover.

  7. REMOVE NO. 2 ROOM LIGHT ASSEMBLY


    1. A01NGX2E01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver wrapped with protective tape, disengage the claw.

    2. Disconnect the connector and remove the No. 2 room light assembly.

  8. REMOVE BACK DOOR UPPER TRIM COVER LH


    1. A01NFNAE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the 2 claws and remove the back door upper trim cover LH as shown in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.

  9. REMOVE BACK DOOR UPPER TRIM COVER RH


    1. A01NF77E01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the 2 claws and remove the back door upper trim cover RH as shown in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.

  10. REMOVE BACK DOOR SERVICE HOLE COVER LH


    1. A01NH4X

      Disengage the 5 claws and remove the back door service hole cover LH.

  11. REMOVE BACK DOOR SERVICE HOLE COVER RH


    1. A01NCYF

      Disengage the 5 claws and remove the back door service hole cover RH.

  12. REMOVE BACK DOOR TRIM PANEL ASSEMBLY


    1. A01NHSL

      Remove the 2 screws.

    2. A01NDQVE01

      Grab the service holes by hand.

      Note

      Make sure to hold the clip bases as shown in the illustration.

    3. Pull the back door trim panel assembly in the direction shown by the arrows in the illustration (pull perpendicular to the surface of the trim panel) to disengage the 2 claws and 16 clips, and remove the back door trim panel assembly.

      Text in Illustration
      *1 2-piece Type Clip

      Note

      Removing the back door trim panel assembly at an angle may cause deformation or damage. To avoid this, make sure to pull the panel in the direction shown by the arrows (pull perpendicular to the surface of the panel).

      Tech Tips

      If any clips remain on the back door panel after the back door trim panel assembly is removed, remove the clips and install them to the back door trim panel assembly.

  13. REMOVE BACK DOOR LOCK ASSEMBLY (w/o Power Back Door)


    1. A01NH1W

      Disconnect the connector.

    2. A01NHZM

      Remove the 3 bolts and back door lock assembly.

  14. REMOVE BACK DOOR LOCK ASSEMBLY (w/ Power Back Door)


    1. A01NDDF

      Disconnect the connector.

    2. Disengage the clamp.

    3. Remove the bolt.

    4. A01ND92

      Remove the 3 bolts and back door lock assembly.