HOOD LOCK CONTROL CABLE ASSEMBLY REMOVAL


  1. REMOVE ENGINE ROOM SIDE COVER


    1. A01NHKG

      Remove the 4 clips and engine room side cover.

  2. REMOVE ENGINE ROOM SIDE COVER LH


    1. A01NH7B

      Remove the 4 clips.

    2. Disengage the guide and remove the engine room side cover LH.

  3. REMOVE COOL AIR INTAKE DUCT SEAL


    1. A01NDNO

      Remove the 6 clips and cool air intake duct seal.

  4. REMOVE HOOD CENTER CUSHION


    1. A01NE5D

      Remove the 2 hood center cushions.

  5. REMOVE FRONT BUMPER ASSEMBLY


    1. A01NFTPE01
      Text in Illustration
      *1 Protective Tape

      Put protective tape around the front bumper assembly.

      Tech Tips

      Use the same procedure for the RH side and LH side.

    2. A01ND22

      Using a screwdriver, turn the pins 90 degrees and remove the 2 pin hold clips.

      Tech Tips

      Use the same procedure for the RH side and LH side.

    3. A01NDQH

      Remove the screw and front bumper seal bracket.

      Tech Tips

      Use the same procedure for the RH side and LH side.

    4. A01NE3M

      Remove the 2 bolts and 2 screws.

    5. Using a clip remover, remove the 6 clips.

    6. A01NFX1

      Disengage the 4 claws and remove the front bumper assembly.

      Tech Tips

      Use the same procedure for the RH side and LH side.

    7. A01NE8W

      Using a moulding remover, disengage the claw.

      Tech Tips

      Use the same procedure for the RH side and LH side.

    8. Disconnect the fog light connector.

    9. Disconnect the No. 1 ultrasonic sensor connector. (w/ LEXUS Parking Assist-sensor System)

    10. Disconnect the headlight cleaner hose.

      Note

      Prepare a drain pan or a piece of cloth in case washer fluid leaks.

    11. A01NCNT

      Remove the front bumper assembly as shown in the illustration.

  6. REMOVE FRONT FENDER TOP REINFORCEMENT SUB-ASSEMBLY LH


    1. A01NDFEE01
      Text in Illustration
      *1 Hood to Cowl Top Seal

      Disengage the clip and the hood to cowl top seal from the front fender top reinforcement sub-assembly LH.

    2. A01NDRP

      Remove the clip.

    3. Disengage the 3 clips and 2 guides, and remove the front fender top reinforcement sub-assembly LH.

  7. REMOVE FRONT FENDER TOP REINFORCEMENT SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and LH side.

  8. REMOVE FRONT FENDER TO COWL SIDE SEAL LH


    1. A01NEBLE01
      Text in Illustration
      *1 Double-sided Tape

      Disengage the 2 claws and remove the front fender to cowl side seal LH.

  9. REMOVE FRONT FENDER TO COWL SIDE SEAL RH

    Tech Tips

    Use the same procedure for the RH side and LH side.

  10. REMOVE FRONT WIPER ARM HEAD CAP


    1. A01NGAME01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the 3 claws and remove the front wiper arm head cap.

      Tech Tips

      Tape the screwdriver tip before use.

  11. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    1. A01NG4G

      Remove the nut and the front wiper arm and blade assembly LH.

  12. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH


    1. A01NEOE

      Remove the 2 nuts and the front wiper arm and blade assembly RH.

  13. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    1. Remove the 2 clips.

      A01ND3VE01

    2. Disengage the 6 claws and guide <A>.

    3. Disengage the 10 guides and pull out the cowl top ventilator louver sub-assembly as shown in the illustration.

  14. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

    2. A01NGYT

      w/o Deicer:


      1. Disconnect the connector.

      2. Disengage the clamp.

    3. A01NEA8

      w/ Deicer:


      1. Disconnect the 2 connectors.

      2. Disengage the clamp.

    4. A01NG3N

      Remove the 5 bolts and the windshield wiper motor and link assembly.

      Note

      Be careful not to damage the windshield when removing the windshield wiper motor and link assembly.

  15. REMOVE FRONT SHOCK ABSORBER CAP LH (w/ Air Suspension)


    1. A01NHTO

      Remove the 3 nuts and front shock absorber cap.

  16. REMOVE FRONT SHOCK ABSORBER CAP RH (w/ Air Suspension)

    Tech Tips

    Use the same procedure for the RH side and LH side.

  17. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY


    1. A01NHCW

      Disconnect the connector (w/ Windshield Deicer).

    2. Disengage the grommet and clamp, and separate the wire harness.

    3. A01NFEQ

      Remove the 6 nuts, 4 bolts and outer cowl top panel sub-assembly.

  18. REMOVE MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Dynamic Radar Cruise Control System)


    1. A01NFIV

      Disconnect the connector.

    2. Remove the 3 bolts and the millimeter wave radar sensor assembly.

  19. REMOVE LOW PITCHED HORN ASSEMBLY (for LHD)


    1. A01NG9V

      Disconnect the connector.

    2. Remove the bolt and low pitched horn assembly.

  20. REMOVE HIGH PITCHED HORN ASSEMBLY (for RHD)


    1. A01NDP3

      Disconnect the connector.

    2. Remove the bolt and high pitched horn assembly.

  21. REMOVE SMOG VENTILATION SENSOR (for RHD)


    1. A01NDOW

      Disconnect the connector.

    2. Remove the bolt

    3. Disengage the guide and remove the smog ventilation sensor.

  22. REMOVE HOOD LOCK CONTROL CABLE COVER (for LHD)


    1. A01NEIY

      Remove the 3 screws.

    2. Disengage the clamp and remove the hood lock control cable cover.

  23. REMOVE HOOD LOCK CONTROL CABLE COVER (for RHD)


    1. A01NDKG

      Remove the 3 screws.

    2. Disengage the clamp and remove the hood lock control cable cover.

  24. REMOVE HOOD LOCK ASSEMBLY (for LHD)


    1. A01NEL1E01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, remove the hood lock nut cap.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01NFDN

      Remove the 2 bolts and hood lock nut.

    3. A01NHW4

      Disconnect the connector.

    4. Disconnect the hood lock control cable and remove the hood lock assembly.

  25. REMOVE HOOD LOCK ASSEMBLY (for RHD)


    1. A01NE7PE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, remove the hood lock nut cap.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01NF9X

      Remove the 2 bolts and hood lock nut.

    3. A01NH3T

      Disconnect the connector.

    4. Disconnect the hood lock control cable and remove the hood lock assembly.

  26. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)


    1. A01NG9O

      Remove the 2 screws <D>.

    2. A01NE3Q

      Disengage the claw and 2 guides as shown in the illustration.

    3. Disconnect each connector.

    4. Disengage each clamp and remove the No. 1 instrument panel under cover sub-assembly.

  27. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)


    1. A01NF7E

      Remove the 2 screws <D>.

    2. A01NHV4

      Disengage the claw and 2 guides as shown in the illustration.

    3. Disconnect each connector.

    4. Disengage each clamp and remove the No. 1 instrument panel under cover sub-assembly.

  28. REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. A01NDQF

      Disengage the 3 claws.

    2. A01NCQN

      Remove the hood lock control cable assembly and hood lock control lever sub-assembly.

  29. REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY (for LHD)


    1. Using a screwdriver, disconnect the clamps shown in the illustration.

      A01NDFDE01
      Text in Illustration
      *1 Hood Lock Control Cable *2 Stopper

      Tech Tips

      Tape the screwdriver tip before use.

    2. Pull the hood lock control cable assembly from the engine compartment and remove it.

  30. REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY (for RHD)


    1. Using a screwdriver, disconnect the clamps shown in the illustration.

      A01NHEZE01
      Text in Illustration
      *1 Hood Lock Control Cable *2 Stopper

      Tech Tips

      Tape the screwdriver tip before use.

    2. Pull the hood lock control cable assembly from the engine compartment and remove it.