CAN COMMUNICATION SYSTEM TERMINALS OF ECU

Note


  • Turn the power switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.

  • Turn the power switch off before inspecting CAN bus wires for a ground short.

  • After the power switch is turned off, check that the key reminder warning system and light reminder warning system are not operating.

  • Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the power switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

  • This section describes the standard CAN values for all CAN related components.

Tech Tips


  • Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

  • Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.


  1. CAN NO. 1 JUNCTION CONNECTOR (for LHD)


    1. Check the CAN No. 1 junction connector.

      A01NG0LE15
      Text in Illustration
      *1

      Front view of wire harness connector

      (to CAN No. 1 Junction Connector)

      		 *2 to Power Steering ECU
      *3 to Steering Angle Sensor *4 to DLC3
      *5 to Combination Meter *6 to Main Body ECU
      *7 to CAN No. 2 Junction Connector *8 to Power Management Control ECU
      *9 to Center Airbag Sensor Assembly *10 to Yaw Rate Sensor

    2. Check the connection diagram of the components which are connected to the CAN No. 1 junction connector.

      Terminal No. (Symbol) Wiring Color Connected to
      F70-1 (CANH) G Power steering ECU
      F70-12 (CANL) R
      F70-2 (CANH) BE Steering angle sensor
      F70-13 (CANL) R
      F70-3 (CANH) V DLC3
      F70-14 (CANL) R
      F70-4 (CANH) P Combination meter
      F70-15 (CANL) R
      F70-5 (CANH) Y Main body ECU
      F70-16 (CANL) R
      F70-7 (CANH) B CAN No. 2 junction connector
      F70-18 (CANL) R
      F70-9 (CANH) LG Power management control ECU
      F70-20 (CANL) R
      F70-10 (CANH) R Center Airbag Sensor
      F70-21 (CANL) L
      F70-11 (CANH) BR Yaw rate sensor
      F70-22 (CANL) R

  2. CAN NO. 2 JUNCTION CONNECTOR (for LHD)


    1. Check the CAN No. 2 junction connector.

      A01NG0LE16
      Text in Illustration
      *1

      Front view of wire harness connector

      (to CAN No. 2 Junction Connector)

      		 *2 to Skid Control ECU
      *3 to Certification ECU *4 to CAN No. 1 Junction Connector
      *5 to Navigation ECU *6 to ECM

    2. Check the connection diagram of the components which are connected to the CAN No. 2 junction connector.

      Terminal No. (Symbol) Wiring Color Connected to
      F71-1 (CANH) GR Skid control ECU
      F71-12 (CANL) R
      F71-2 (CANH) LG Certification ECU
      F71-13 (CANL) R
      F71-7 (CANH) B CAN No. 1 junction connector
      F71-18 (CANL) R
      F71-8 (CANH) SB Navigation ECU
      F71-19 (CANL) R
      F71-9 (CANH) GR ECM
      F71-20 (CANL) R

  3. CAN NO. 3 JUNCTION CONNECTOR (for LHD)


    1. Check the CAN No. 3 junction connector.

      A01NG0LE17
      Text in Illustration
      *1

      Front view of wire harness connector

      (to CAN No. 3 Junction Connector)

      		 *2 to Suspension Control ECU
      *3 to Seat Belt Control ECU *4

      • to Parking Assist ECU

        (w/ Parking Assist Monitor system)

      • to Clearance Warning ECU

        (w/ LEXUS Parking Assist-sensor system)
      *5 to CAN No. 4 Junction Connector *6 to Power Management Control ECU

    2. Check the connection diagram of the components which are connected to the CAN No. 3 junction connector.

      Terminal No. (Symbol) Wiring Color Connected to
      F67-2 (CANH) P Suspension Control ECU
      F67-13 (CANL) L
      F67-3 (CANH) V Seat Belt Control ECU
      F67-14 (CANL) L
      F67-4 (CANH) Y

      • Parking assist ECU

        (w/ Parking assist monitor system)

      • Clearance warning ECU

        (w/ LEXUS parking assist-sensor system)
      F67-15 (CANL) L
      F67-6 (CANH) BR CAN No. 4 junction connector
      F67-17 (CANL) L
      F67-7 (CANH) G Power Management Control ECU
      F67-18 (CANL) L

  4. CAN NO. 4 JUNCTION CONNECTOR (for LHD)


    1. Check the CAN No. 4 junction connector.

      A01NG0LE18
      Text in Illustration
      *1

      Front view of wire harness connector

      (to CAN No. 4 Junction Connector)

      		 *2 to Driving Support ECU
      *3 to AFS ECU *4 to CAN No. 3 Junction Connector
      *5 to CAN No. 5 Junction Connector - -

    2. Check the connection diagram of the components which are connected to the CAN No. 4 junction connector.

      Terminal No. (Symbol) Wiring Color Connected to
      F68-2 (CANH) BE Driving support ECU
      F68-13 (CANL) L
      F68-3 (CANH) B AFS ECU
      F68-14 (CANL) L
      F68-4 (CANH) BR CAN No. 3 junction connector
      F68-15 (CANL) L
      F68-8 (CANH) GR CAN No. 5 junction connector
      F68-19 (CANL) L

  5. CAN NO. 1 JUNCTION CONNECTOR (for RHD)


    1. Check the CAN No. 1 junction connector.

      A01NG0LE19
      Text in Illustration
      *1

      Front view of wire harness connector

      (to CAN No. 1 Junction Connector)

      		 *2 to Main Body ECU
      *3 to CAN No. 2 Junction Connector *4 to Navigation ECU
      *5 to Power Management Control ECU *6 to Center Airbag Sensor Assembly
      *7 to Yaw Rate Sensor - -

    2. Check the connection diagram of the components which are connected to the CAN No. 1 junction connector.

      Terminal No. (Symbol) Wiring Color Connected to
      F70-5 (CANH) Y Main body ECU
      F70-16 (CANL) R
      F70-7 (CANH) B CAN No. 2 junction connector
      F70-18 (CANL) R
      F70-8 (CANH) SB Navigation ECU
      F70-19 (CANL) R
      F70-9 (CANH) LG Power management control ECU
      F70-20 (CANL) R
      F70-10 (CANH) R Center Airbag Sensor
      F70-21 (CANL) L
      F70-11 (CANH) BR Yaw rate sensor
      F70-22 (CANL) R

  6. CAN NO. 2 JUNCTION CONNECTOR (for RHD)


    1. Check the CAN No. 2 junction connector.

      A01NG0LE08
      Text in Illustration
      *1

      Front view of wire harness connector

      (to CAN No. 2 Junction Connector)

      		 *2 to Skid Control ECU
      *3 to Certification ECU *4 to DLC3
      *5 to Combination Meter *6 to Steering Angle Sensor
      *7 to Power Steering ECU *8 to CAN No. 1 Junction Connector

    2. Check the connection diagram of the components which are connected to the CAN No. 2 junction connector.

      Terminal No. (Symbol) Wiring Color Connected to
      F71-1 (CANH) GR Skid control ECU
      F71-12 (CANL) R
      F71-2 (CANH) LG Certification ECU
      F71-13 (CANL) R
      F71-3 (CANH) V DLC3
      F71-14 (CANL) R
      F71-4 (CANH) P Combination meter
      F71-15 (CANL) R
      F71-5 (CANH) BE Steering angle sensor
      F71-16 (CANL) R
      F71-6 (CANH) G Power steering ECU
      F71-17 (CANL) R
      F71-7 (CANH) B CAN No. 1 junction connector
      F71-18 (CANL) R

  7. CAN NO. 3 JUNCTION CONNECTOR (for RHD)


    1. Check the CAN No. 3 junction connector.

      A01NG0LE20
      Text in Illustration
      *1

      Front view of wire harness connector

      (to CAN No. 3 Junction Connector)

      		 *2 to CAN No. 4 Junction Connector
      *3 to Driving Support ECU *4 to AFS ECU
      *5 to Power Management Control ECU - -

    2. Check the connection diagram of the components which are connected to the CAN No. 3 junction connector.

      Terminal No. (Symbol) Wiring Color Connected to
      F67-6 (CANH) BR CAN No. 4 junction connector
      F67-17 (CANL) L
      F67-7 (CANH) BE Driving support ECU
      F67-18 (CANL) L
      F67-8 (CANH) B AFS ECU
      F67-19 (CANL) L
      F67-9 (CANH) G Power Management Control ECU
      F67-20 (CANL) L

  8. CAN NO. 4 JUNCTION CONNECTOR (for RHD)


    1. Check the CAN No. 4 junction connector.

      A01NG0LE21
      Text in Illustration
      *1

      Front view of wire harness connector

      (to CAN No. 4 Junction Connector)

      		 *2 to CAN No. 3 Junction Connector
      *3 to Seat Belt Control ECU *4

      • to Parking Assist ECU

        (w/ Parking Assist Monitor system)

      • to Clearance Warning ECU

        (w/ LEXUS Parking Assist-sensor system)
      *5 to Suspension Control ECU *6 to CAN No. 5 Junction Connector

    2. Check the connection diagram of the components which are connected to the CAN No. 4 junction connector.

      Terminal No. (Symbol) Wiring Color Connected to
      F68-4 (CANH) BR CAN No. 3 junction connector
      F68-15 (CANL) L
      F68-5 (CANH) V Seat belt control ECU
      F68-16 (CANL) L
      F68-6 (CANH) Y

      • Parking assist ECU

        (w/ Parking assist monitor system)

      • Clearance warning ECU

        (w/ LEXUS parking assist-sensor system)
      F68-17 (CANL) L
      F68-7 (CANH) P Suspension Control ECU
      F68-18 (CANL) L
      F68-8 (CANH) GR CAN No. 5 junction connector
      F68-19 (CANL) L

  9. CAN NO. 5 JUNCTION CONNECTOR

    Tech Tips

    - The connectors connected to the CAN junction connectors can be distinguished according to the color of the communication bus wires.

    - Reconnecting the connectors to non-specified positions on the CAN junction connectors does not affect system operation. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.


    1. Check the CAN No. 5 junction connectors.

      A01NGZRE01
      Text in Illustration
      *1

      Component without harness connected

      (CAN No. 5 Junction Connector)

      		 *2 CAN No. 5 Junction Connector B Side
      *3 CAN No. 5 Junction Connector A Side *4 Ground Terminal
      *5

      Front view of wire harness connector

      (to CAN No. 5 Junction Connector)

      		 - -

    2. Check the connection diagram of the components which are connected to the CAN No. 5 junction connector.

      Terminal No. (Symbol) Wiring Color Connected to
      P56-1 W-B Ground
      P55-1 (CANH) L CAN No. 4 junction connector
      P55-2 (CANL) Y
      P54-1 (CANH) V Rear active stabilizer control ECU
      P54-2 (CANL) LG
      P53-1 (CANH) R Front active stabilizer control ECU
      P53-2 (CANL) G

  10. CAN NO. 6 JUNCTION CONNECTOR


    1. Check the CAN No. 6 junction connector.

      A01NG0LE22
      Text in Illustration
      *1

      Front view of wire harness connector

      (to CAN No. 6 Junction Connector)

      		 *2 to Front Power Seat Switch LH
      *3

      to CAN No. 7 Junction Connector

      (w/ Power Back Door System)

      		 *3

      to CAN No. 8 Junction Connector

      (w/o Power Back Door System)
      *4 to Main Body ECU *5 to Outer Mirror Control ECU LH

    2. Check the connection diagram of the components which are connected to the CAN No. 6 junction connector.

      Terminal No. (Symbol) Wiring Color Connected to
      F102-2 (CANH) G Front power seat switch LH
      F102-13 (CANL) W
      F102-3 (CANH) B

      CAN No. 7 junction connector

      (w/ power back door system)
      F102-14 (CANL) W
      F102-3 (CANH) B

      CAN No. 8 junction connector

      (w/o power back door system)
      F102-14 (CANL) W
      F102-4 (CANH) BE Main body ECU
      F102-15 (CANL) W
      F102-5 (CANH) LG Outer mirror control ECU LH
      F102-16 (CANL) W

  11. CAN NO. 7 JUNCTION CONNECTOR


    1. Check the CAN No. 7 junction connector.

      A01NG0LE23
      Text in Illustration
      *1

      Front view of wire harness connector

      (to CAN No. 7 Junction Connector)

      		 *2 to CAN No. 8 Junction Connector
      *3

      Power Back Door ECU

      (Back Door Monitor Unit)

      		 *4 to CAN No. 6 Junction Connector

    2. Check the connection diagram of the components which are connected to the CAN No. 7 junction connector.

      Terminal No. (Symbol) Wiring Color Connected to
      P66-1 (CANH) B CAN No. 8 junction connector
      P66-12 (CANL) W
      P66-2 (CANH) B

      Power back door ECU

      (Back motor unit)
      P66-13 (CANL) W
      P66-3 (CANH) B CAN No. 6 junction connector
      P66-14 (CANL) W

  12. CAN NO. 8 JUNCTION CONNECTOR


    1. Check the CAN No. 8 junction connector.

      A01NG0LE35
      Text in Illustration
      *1

      Front view of wire harness connector

      (to CAN No. 8 Junction Connector)

      		 *2 to Front Power Seat Switch RH
      *3

      to Tilt and Telescopic ECU

      (Multiplex Tilt and Telescopic ECU)

      		 *4

      to CAN No. 7 Junction Connector

      (w/ Power Back Door System)
      *4

      to CAN No. 6 Junction Connector

      (w/o Power Back Door System)

      		 *5 to Outer Mirror Control ECU RH

    2. Check the connection diagram of the components which are connected to the CAN No. 8 junction connector.

      Terminal No. (Symbol) Wiring Color Connected to
      F103-2 (CANH) G Front power seat switch RH
      F103-13 (CANL) W
      F103-3 (CANH) BE

      Tilt and telescopic ECU

      (Multiplex tilt and telescopic ECU)
      F103-14 (CANL) W
      F103-4 (CANH) B

      CAN No. 7 junction connector

      (w/ Power back door system)
      F103-15 (CANL) W
      F103-4 (CANH) B

      CAN No. 6 junction connector

      (w/o Power back door system)
      F103-15 (CANL) W
      F103-5 (CANH) LG Outer mirror control ECU RH
      F103-16 (CANL) W

  13. CAN NO. 9 JUNCTION CONNECTOR


    1. Check the CAN No. 9 junction connector.

      A01NG0LE25
      Text in Illustration
      *1

      Front view of wire harness connector

      (to CAN No. 9 Junction Connector)

      		 *2 to Air Conditioning Amplifier
      *3 to Power Management Control ECU *4 to ECM
      *5 to Skid Control ECU - -

    2. Check the connection diagram of the components which are connected to the CAN No. 9 junction connector.

      Terminal No. (Symbol) Wiring Color Connected to
      F72-1 (CANH) B Air conditioning amplifier
      F72-12 (CANL) W
      F72-2 (CANH) V Power management control ECU
      F72-13 (CANL) W
      F72-3 (CANH) G ECM
      F72-14 (CANL) W
      F72-4 (CANH) P Skid control ECU
      F72-15 (CANL) W

  14. CAN NO. 10 JUNCTION CONNECTOR

    Tech Tips

    - The connectors connected to the CAN junction connectors can be distinguished according to the color of the communication bus wires.

    - Reconnecting the connectors to non-specified positions on the CAN junction connectors does not affect system operation. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.


    1. Check the CAN No. 10 junction connectors.

      A01NG1ME01
      Text in Illustration
      *1

      Component without harness connected

      (CAN No. 10 Junction Connector)

      		 *2 CAN No. 10 Junction Connector B Side
      *3 CAN No. 10 Junction Connector A Side *4 Ground Terminal
      *5

      Front view of wire harness connector

      (to CAN No. 10 Junction Connector)

      		 - -

    2. Check the connection diagram of the components which are connected to the CAN No. 10 junction connector.

      Terminal No. (Symbol) Wiring Color Connected to
      P60-1 W-B Ground
      P59-1 (CANH) B Skid control ECU
      P59-2 (CANL) W
      P58-1 (CANH) B Rear active stabilizer control ECU
      P58-2 (CANL) W
      P57-1 (CANH) L Front active stabilizer control ECU
      P57-2 (CANL) Y

  15. DLC3


    1. Measure the resistance according to the value(s) in the table below.

      A01NHACE08
      Text in Illustration
      *1 DLC3

    2. ECM


      1. A01NEJ1E06
      3. Text in Illustration
      *1

      Front view of wire harness connector

      (to ECM)

    Disconnect the connector of the ECM.

  16. Measure the resistance according to the value(s) in the table below.

  17. MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

    A01NFOME05

    1. Disconnect the connectors of the main body ECU.

      A01NGGUE02
    18. Text in Illustration
    *1

    Front view of wire harness connector

    (to Main Body ECU)

    		 *2 DLC3

  • Measure the resistance according to the value(s) in the table below.

  • COMBINATION METER


    1. Disconnect the connector of the combination meter.

      A01NEFIE02
    • Text in Illustration
    *1

    Front view of wire harness connector

    (to Combination Meter)

  • Measure the resistance according to the value(s) in the table below.

  • POWER STEERING ECU


    1. Disconnect the connectors of the power steering ECU.

      A01NDECE06
    • Text in Illustration
    *1

    Front view of wire harness connector

    (to Power Steering ECU)

  • Measure the resistance according to the value(s) in the table below.

  • AIR CONDITIONING AMPLIFIER


    1. Disconnect the connector of the air conditioning amplifier.

      A01NEG3E08
    • Text in Illustration
    *1

    Front view of wire harness connector

    (to Air Conditioning Amplifier)

  • Measure the resistance according to the value(s) in the table below.

  • CENTER AIRBAG SENSOR ASSEMBLY


    1. Disconnect the connector of the center airbag sensor assembly.

      A01NHJLE08
    • Text in Illustration
    *1

    Front view of wire harness connector

    (to Center Airbag Sensor Assembly)

    		 *2 DLC3

  • Measure the resistance according to the value(s) in the table below.

  • SKID CONTROL ECU


    1. A01NDBHE01
    • Text in Illustration
    *1

    Front view of wire harness connector

    (to Skid Control ECU)

    Disconnect the connector of the skid control ECU.

  • Measure the resistance according to the value(s) in the table below.

  • STEERING ANGLE SENSOR


    1. A01NH8SE26
    • Text in Illustration
    *1

    Front view of wire harness connector

    (to Steering Angle Sensor)

    Disconnect the connector of the steering angle sensor.

  • Measure the resistance according to the value(s) in the table below.

  • YAW RATE SENSOR


    1. A01NE4PE14
    • Text in Illustration
    *1

    Front view of wire harness connector

    (to Yaw Rate Sensor)

    Disconnect the connector of the yaw rate sensor.

  • Measure the resistance according to the value(s) in the table below.

  • CERTIFICATION ECU (SMART KEY ECU)


    1. Disconnect the connector of the certification ECU.

      A01NF1OE02
    • Text in Illustration
    *1

    Front view of wire harness connector

    (to Certification ECU)

  • Measure the resistance according to the value(s) in the table below.

  • NAVIGATION ECU (DISPLAY AND NAVIGATION MODULE DISPLAY)

    A01NGMEE01

    1. A01NDYVE01
    • Text in Illustration
    *1

    Front view of wire harness connector

    (to Display and Navigation Module Display)

    Disconnect the connector of the navigation ECU.

  • Measure the resistance according to the value(s) in the table below.

  • POWER MANAGEMENT CONTROL ECU


    1. A01NDSPE01
    • Text in Illustration
    *1

    Rear view of wire harness connector

    (to Power Management control ECU)

    Disconnect the connectors of the power management control ECU.

  • Measure the resistance according to the value(s) in the table below.

    • Standard Resistance
    for CAN No. 1 Bus Main Wire
    Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
    F98-25 (CA1H) - F98-24 (CA1L) LG - R HIGH-level CAN bus line - LOW-level CAN bus line Power switch off 108 to 132 Ω
    F98-25 (CA1H) - F98-7 (AM21) LG - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
    F98-24 (CA1L) - F98-7 (AM21) R - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
    F98-25 (CA1H) - F97-6 (E1) LG - BR HIGH-level CAN bus line - Ground Power switch off 200 Ω or higher
    F98-24 (CA1L) - F97-6 (E1) R - BR LOW-level CAN bus line - Ground Power switch off 200 Ω or higher
    for CAN No. 2 Bus Main Wire
    Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
    F97-34 (CA2H) - F97-35 (CA2L) G - L HIGH-level CAN bus line - LOW-level CAN bus line Power switch off 108 to 132 Ω
    F97-34 (CA2H) - F98-7 (AM21) G - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
    F97-35 (CA2L) - F98-7 (AM21) L - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
    F97-34 (CA2H) - F97-6 (E1) G - BR HIGH-level CAN bus line - Ground Power switch off 200 Ω or higher
    F97-35 (CA2L) - F97-6 (E1) L - BR LOW-level CAN bus line - Ground Power switch off 200 Ω or higher
    for Power Management Bus Main Wire
    Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
    F98-31 (CA3P) - F98-30 (CA3N) V - W HIGH-level CAN bus line - LOW-level CAN bus line Power switch off 108 to 132 Ω
    F98-31 (CA3P) - F98-7 (AM21) V - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
    F98-30 (CA3N) - F98-7 (AM21) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
    F98-31 (CA3P) - F97-6 (E1) V - BR HIGH-level CAN bus line - Ground Power switch off 200 Ω or higher
    F98-30 (CA3N) - F97-6 (E1) W - BR LOW-level CAN bus line - Ground Power switch off 200 Ω or higher

  • AFS ECU (HEADLIGHT SWIVEL ECU)


    1. Disconnect the connector of the AFS ECU.

      A01NHVYE04
      Text in Illustration
      *1

      Front view of wire harness connector

      (to AFS ECU)

      		 *2 DLC3

    2. Measure the resistance according to the value(s) in the table below.

    3. SUSPENSION CONTROL ECU

      A01NHG2E08

      1. A01NE3EE26
      4. Text in Illustration
      *1

      Rear view of wire harness connector

      (to Suspension Control ECU)

    Disconnect the connector of the suspension control ECU.

  • Measure the resistance according to the value(s) in the table below.

  • SEAT BELT CONTROL ECU

    A01NFGFE01
    • Text in Illustration
    *1

    Front view of wire harness connector

    (to Seat Belt Control ECU)

    1. Disconnect the connectors of the seat belt control ECU.

    2. Measure the resistance according to the value(s) in the table below.

    3. DRIVING SUPPORT ECU

      A01NHANE01
      4. Text in Illustration
      *1

      Rear view of wire harness connector

      (to Driving Support ECU)

      1. Disconnect the connector of the driving support ECU.

      2. Measure the resistance according to the value(s) in the table below.

      3. PARKING ASSIST ECU


        1. A01NEXPE01
        4. Text in Illustration
        *1

        Front view of wire harness connector

        (to Parking Assist ECU)

        Disconnect the connector of the parking assist ECU.

      4. Measure the resistance according to the value(s) in the table below.

      5. CLEARANCE WARNING ECU


        1. Disconnect the connector of the clearance warning ECU.

          A01NFLJE02
        6. Text in Illustration
        *1

        Front view of wire harness connector

        (to Clearance Warning ECU)

        		 *2 DLC3

      6. Measure the resistance according to the value(s) in the table below.

      7. TILT AND TELESCOPIC ECU (MULTIPLEX TILT AND TELESCOPIC ECU)

        A01NG0GE01
        8. Text in Illustration
        *1

        Rear view of wire harness connector

        (to Multiplex Tilt and Telescopic ECU)

        1. Disconnect the connector of the multiplex tilt and telescopic ECU.

        2. Measure the resistance according to the value(s) in the table below.

        3. OUTER MIRROR CONTROL ECU RH


          1. A01NDWAE02
          4. Text in Illustration
          *1

          Front view of wire harness connector

          (to Outer Mirror Control ECU RH)

          Disconnect the connector of the outer mirror control ECU RH.

        4. Measure the resistance according to the value(s) in the table below.

        5. OUTER MIRROR CONTROL ECU LH


          1. A01NDWAE01
          6. Text in Illustration
          *1

          Front view of wire harness connector

          (to Outer Mirror Control ECU LH)

          Disconnect the connector of the outer mirror control ECU LH.

        6. Measure the resistance according to the value(s) in the table below.

        7. FRONT POWER SEAT SWITCH RH


          1. Disconnect the connectors of the front power seat switch RH.

            A01NH9FE02
          8. Text in Illustration
          *1

          Front view of wire harness connector

          (to Front Power Seat Switch RH)

        8. Measure the resistance according to the value(s) in the table below.

        9. FRONT POWER SEAT SWITCH LH


          1. Disconnect the connectors of the front power seat switch LH.

            A01NH9FE01
          10. Text in Illustration
          *1

          Front view of wire harness connector

          (to Front Power Seat Switch LH)

        10. Measure the resistance according to the value(s) in the table below.

        11. POWER BACK DOOR ECU (BACK DOOR MOTOR UNIT)


          1. Disconnect the connector of the power back door ECU (back door motor unit).

            A01NFMUE04
          12. Text in Illustration
          *1

          Front view of wire harness connector

          (to Power Back Door ECU)

        12. Measure the resistance according to the value(s) in the table below.

        13. FRONT ACTIVE STABILIZER CONTROL ECU


          1. Disconnect the connector of the front active stabilizer control ECU.

            A01NDXLE01
          14. Text in Illustration
          *1

          Front view of wire harness connector

          (to Front Active Stabilizer Control ECU)

          		 *2 DLC3

        14. Measure the resistance according to the value(s) in the table below.

        15. REAR ACTIVE STABILIZER CONTROL ECU


          1. Disconnect the connector of the rear active stabilizer control ECU.

            A01NDXLE02
          16. Text in Illustration
          *1

          Front view of wire harness connector

          (to Rear Active Stabilizer Control ECU)

          		 *2 DLC3

        16. Measure the resistance according to the value(s) in the table below.