LIN COMMUNICATION SYSTEM, Diagnostic DTC:B1206

DTC Code DTC Name
B1206 P/W Master Switch Communication Stop

DESCRIPTION

This DTC is stored when LIN communication between the multiplex network master switch assembly and main body ECU (multiplex network body ECU) stops for more than 10 seconds.

DTC No. DTC Detection Condition Trouble Area
B1206 No communication between multiplex network master switch assembly and main body ECU (multiplex network body ECU) for more than 10 seconds.

  • Multiplex network master switch assembly

  • Main body ECU (multiplex network body ECU)

  • Instrument panel junction block assembly

  • Wire harness or connector

  • ECU-B NO. 2 fuse

WIRING DIAGRAM

A01NHTBE17

INSPECTION PROCEDURE

Note

When using the intelligent tester to troubleshoot with the power switch off:

Connect the intelligent tester to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

PROCEDURE


  1. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    1. Remove the instrument panel junction block assembly Click here.

      A01NGJME01

    2. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Tech Tips

      This inspection is to check the LIN line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).

      Standard Resistance
      Tester Connection Condition Specified Condition
      2D-27 (LIN2) - MB-16 (LIN2) Always Below 1 Ω
      2D-27 (LIN2) - Body ground Always 10 kΩ or higher
      Text in Illustration
      *1

      Component without harness connected

      (Instrument Panel Junction Block Assembly)

      		 *2

      Component without harness connected

      (Instrument Panel Junction Block Assembly)

    NG

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY Click here

    OK

  2. CHECK HARNESS AND CONNECTOR


    1. A01NHPFE02
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Instrument Panel Junction Block Assembly)
      *2

      Front view of wire harness connector

      (to Multiplex Network Master Switch Assembly)
      *3 for LHD
      *4 for RHD

      Disconnect the J7 multiplex network master switch assembly connector*1.

    2. Disconnect the I12 multiplex network master switch assembly connector*2.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition

      2D-27 (LIN2) - J7-17 (LIN1)*1

      2D-27 (LIN2) - I12-17 (LIN1)*2

      		 Always Below 1 Ω
      2D-27 (LIN2) - Body ground Always 10 kΩ or higher

      • *1: for LHD

      • *2: for RHD


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HARNESS AND CONNECTOR


    1. A01NGQAE05
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Multiplex Network Master Switch Assembly)
      *2 for LHD
      *3 for RHD

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition

      2D-27 (LIN2) - J7-17 (LIN1)*1

      2D-27 (LIN2) - I12-17 (LIN1)*2

      		 Always 11 to 14 V

      • *1: for LHD

      • *2: for RHD


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY


    1. Replace the multiplex network master switch assembly Click here.


    NEXT

  5. CHECK DTC OUTPUT


    1. Clear the DTC Click here.

    2. Recheck for DTCs.

      OK
      DTC B1206 is not output.

    NG

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    OK

    END (MULTIPLEX NETWORK MASTER SWITCH WAS DEFECTIVE)