ULTRASONIC SENSOR (for Rear Side) INSTALLATION


  1. INSTALL NO. 1 ULTRASONIC SENSOR RETAINER (for Corner Sensor)


    1. A01NGMIE01
      Text in Illustration
      *1 Protrusion
      *2 Keyhole

      Temporarily install the No. 1 ultra sonic sensor retainer to the rear bumper.

      Note


      • Do not damage the rear bumper with the protrusion when installing the retainer.

      • Securely install the No. 1 ultrasonic sensor retainer so that there are no gaps between the retainer and surface of the rear bumper.

      Tech Tips


      • When installing the retainer, align the keyhole and protrusion as shown in the illustration.

      • Use the same procedure for the RH side and LH side.

    2. A01NH43

      Engage the 2 claws to install the No. 1 ultrasonic sensor retainer.

      Tech Tips

      Use the same procedure for the RH side and LH side.

  2. INSTALL NO. 1 ULTRASONIC SENSOR (for Corner Sensor)


    1. A01NHTR

      Engage the 2 claws to install the No. 1 ultrasonic sensor.

      Note

      Push the No. 1 ultrasonic sensor retainer from the outside of the bumper when there is a gap between the retainer and the bumper surface. In this case, do not push on the ultrasonic sensor.

      Tech Tips

      Use the same procedure for the RH side and LH side.

    2. A01NG8S

      Connect the connector.

      Tech Tips

      Use the same procedure for the RH side and LH side.

  3. INSTALL NO. 1 ULTRASONIC SENSOR RETAINER (for Back Sensor)


    1. A01NFQVE01
      Text in Illustration
      *1 Protrusion
      *2 Keyhole

      Temporarily install the No. 1 ultra sonic sensor retainer to the rear bumper.

      Note


      • Do not damage the rear bumper with the protrusion when installing the retainer.

      • Securely install the No. 1 ultrasonic sensor retainer so that there are no gaps between the retainer and surface of the rear bumper.

      Tech Tips


      • When installing the retainer, align the keyhole and protrusion as shown in the illustration.

      • The illustration is for the LH side. The RH side is the opposite of the LH side.

    2. A01NGPP

      Engage the 2 claws to install the No. 1 ultrasonic sensor retainer.

      Tech Tips

      The illustration is for the LH side. The RH side is the opposite of the LH side.

  4. INSTALL NO. 1 ULTRASONIC SENSOR (for Back Sensor)


    1. A01NCV3

      Engage the 2 claws to install the No. 1 ultrasonic sensor.

      Note

      Push the No. 1 ultrasonic sensor retainer from the outside of the bumper when there is a gap between the retainer and the bumper surface. In this case, do not push on the ultrasonic sensor.

      Tech Tips

      The illustration is for the LH side. The RH side is the opposite of the LH side.

    2. A01NFNU

      Connect the connector.

      Tech Tips

      The illustration is for the LH side. The RH side is the opposite of the LH side.

  5. INSTALL REAR BUMPER ASSEMBLY


    1. Connect each connector.

    2. A01NHLV

      Engage the 4 claws and 4 guides, and install the rear bumper assembly as shown in the illustration.

    3. A01NF8V

      Engage the 7 claws.

      Tech Tips

      Use the same procedure for the RH side and LH side.

    4. A01NF9L

      Install the screw.

      Torque:
      2.5 N*m  { 26 kgf*cm, 22 in.*lbf }

      Tech Tips

      Use the same procedure for the RH side and LH side.

    5. A01NGHR

      Engage the 2 rear bumper upper stoppers and install the 2 screws.

      Torque:
      7.5 N*m  { 77 kgf*cm, 66 in.*lbf }
    6. A01NGEW

      Install the 2 clips.

  6. INSTALL NO. 2 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR


    1. A01NGGW

      Engage the 2 craws and install the No. 2 luggage compartment side cover protector.

    2. Install the 3 clips and 2 bolts.

    3. Install the 4 screws.

      Torque:
      7.5 N*m  { 77 kgf*cm, 66 in.*lbf }
    4. A01NGGR

      Install the 2 screws.

      Torque:
      7.5 N*m  { 77 kgf*cm, 66 in.*lbf }

    5. Install a new grommet.

  7. INSTALL NO. 1 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR


    1. A01NEJ9

      Install the No. 1 luggage compartment side cover protector with the 2 clips.

    2. Install the 2 bolts and 2 screws.

  8. INSTALL REAR QUARTER PANEL MUDGUARD SUB-ASSEMBLY LH


    1. A01NDHL

      Using a 4 mm hexagon wrench, install the rear quarter panel mudguard sub-assembly with the 3 hexagon screws.

      Torque:
      7.5 N*m  { 77 kgf*cm, 66 in.*lbf }
    2. A01NFP7

      Install the 2 screws.

      Torque:
      7.5 N*m  { 77 kgf*cm, 66 in.*lbf }

  9. INSTALL REAR QUARTER PANEL MUDGUARD SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and LH side.