SIDE MONITOR SYSTEM Images from All Cameras are Abnormal

DESCRIPTION

The parking assist ECU displays images for the parking assist monitor and side monitor screens. The image signals are sent from the parking assist ECU to the multi-display assembly through the digital communication cable.

WIRING DIAGRAM

A01ND4EE01

INSPECTION PROCEDURE

Note


  • When "System initializing" is displayed on the multi-display after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point Click here.

  • Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the side monitor system may be needed Click here.

Tech Tips

Images are difficult to discern even in normal conditions if:


  • Noise may occur in the image while adjusting or retracting the outer rear view mirror assembly (passenger side).

  • Noise may occur in the image depending on electrical devices used in the cabin.

  • Noise may occur in the image if accessories that generate radio waves have been installed.

  • The camera screen is frosted over (the image immediately after turning the power switch on (IG) may be blurred or darker than normal).

  • The camera lens is dirty with snow, mud, etc.

  • A strong beam of light, such as a sunbeam or headlight, hits the camera.

  • It is too dark around the camera (at night etc.).

  • The ambient temperature around the camera is either too high or too low.

  • The vehicle is tilted at a steep angle.

  • The ambience of the camera is too bright. (When a strong light, such as a sunbeam reflected off the vehicle body, hits the camera, the image may be blurred. This is called the "SMEAR" phenomenon, peculiar to the CCD camera.)

PROCEDURE


  1. CONFIRM SYMPTOMS


    1. Check if the same symptom occurs on the parking assist monitor and side monitor screens.

      Result
      Result Proceed to
      Images from parking assist monitor system and side monitor system are abnormal. A
      Side monitor system is not equipped. A
      Image from parking assist monitor system is normal. B
      Image from side monitor system is normal. C

      Tech Tips


      • Conditions for displaying the parking assist monitor screen (Shift lever in R).

      • Refer to the conditions for displaying the side monitor screen (w/ Side Monitor System) Click here.

      • The parking assist ECU displays images for the parking assist monitor and side monitor screens.

      • Each image signal is sent from the parking assist ECU to the multi-display assembly through the digital communication cable.

      • If the same symptoms occur on the parking assist monitor and side monitor screens, image signals between the parking assist ECU and multi-display assembly may be abnormal.


    B

    GO TO OTHER PROBLEM (IMAGE FROM CAMERA FOR SIDE MONITOR IS ABNORMAL) Click here

    C

    GO TO PARKING ASSIST MONITOR SYSTEM (IMAGE FROM CAMERA FOR PARKING ASSIST MONITOR IS ABNORMAL) Click here

    A

  2. READ VALUE USING INTELLIGENT TESTER


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Chassis / Parking Assist Monitor System / Data List.

    5. Check the Data List for proper functioning of the following items.

      Parking Assist Monitor System
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      AISIC Output Status Output condition of camera display/OK or NG

      OK: Output condition of camera display is normal

      NG: Output condition of camera display is abnormal

      		 -

    NG

    REPLACE PARKING ASSIST ECU Click here

    OK

  3. CHECK DIGITAL COMMUNICATION CABLE CONNECTOR


    1. Check the digital communication cable connector.


      1. Check the digital communication cable connectors between the parking assist ECU and multi-display assembly for any connection problems Click here.

    2. Check if the same malfunction recurs when the parking assist monitor and side monitor screens are displayed.

      Result
      Result Proceed to

      Malfunction does not reoccur

      (returns to normal)

      		 A
      Malfunction reoccurs B

    B

    Click here

    A

    END

  4. REPLACE WIRE HARNESS (DIGITAL COMMUNICATION CABLE)


    1. Replace the digital communication cable between the parking assist ECU and multi-display assembly with a new one.

    2. Check if the same malfunction recurs when the parking assist monitor and side monitor screens are displayed.

      Result
      Result Proceed to

      Malfunction does not reoccur

      (returns to normal)

      		 A
      Malfunction reoccurs B

    B

    Click here

    A

    END

  5. REPLACE MULTI-DISPLAY ASSEMBLY


    1. Replace the multi-display assembly with a new or normally functioning one Click here.

    2. Check if the same malfunction recurs when the parking assist monitor and side monitor screens are displayed.

      Result
      Result Proceed to

      Malfunction does not reoccur

      (returns to normal)

      		 A
      Malfunction reoccurs B

    B

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    A

    END