NAVIGATION RECEIVER (for DVD) INSTALLATION


  1. INSTALL DISPLAY AND NAVIGATION MODULE DISPLAY

  2. INSTALL NO. 4 DISC PLAYER BRACKET


    1. A01NCXP

      Install the No. 4 disc player bracket with the 2 bolts.

  3. INSTALL NO. 3 DISC PLAYER BRACKET


    1. A01NHVR

      Install the No. 3 disc player bracket with the 2 bolts.

  4. INSTALL DISPLAY AND NAVIGATION MODULE DISPLAY WITH BRACKET


    1. Connect each connector.

    2. A01NGHE

      Install the display and navigation module display with bracket as shown in the illustration.

  5. INSTALL MULTI-MEDIA MODULE NAVIGATION ASSEMBLY

  6. INSTALL NO. 2 DISC PLAYER BRACKET


    1. A01NDVL

      Install the No. 2 disc player bracket with the 2 bolts.

  7. INSTALL NO. 1 DISC PLAYER BRACKET


    1. A01NG35

      Install the No. 1 disc player bracket with the 2 bolts.

  8. INSTALL MULTI-MEDIA MODULE NAVIGATION ASSEMBLY WITH BRACKET


    1. A01NEQU

      Engage the guide.

    2. Install the multi-media module navigation assembly with bracket with the 3 bolts.

    3. Connect the 2 connectors.

    4. A01NFCG

      Engage the claw and 3 clamps to install the floor carpet to the original position.

    5. A01NE1F

      Engage the claw and 3 clamps to install the floor carpet to the original position.

  9. INSTALL SHIFT LEVER ASSEMBLY

    Note

    Check that the park/neutral position switch and the shift lever are in neutral.


    1. A01NEY8E02
      Text in Illustration
      *1 Lock Nut
      *2 Push in
      *3 Stopper

      Turn the lock nut of the transmission control cable counterclockwise. While holding the lock nut, push in the stopper.

    2. Connect the outer part of the transmission control cable to the shift lever retainer.

      A01NEXDE02
      Text in Illustration
      *1 Shift Lever Retainer *2 Stopper
      *3 Lock Nut - -

      Note

      The lock nut is fully seated against the shift lever retainer.

    3. A01NF07

      Install the transmission control cable end to the shift lever assembly.

      Note


      • Install the floor shift cable with the uneven surface facing up.

      • Install the cable end all the way to the base of the pin.

    4. A01NDSO

      Install the shift lever assembly with the 4 nuts.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

    5. Connect the 3 clamps to the shift lever assembly.

    6. Connect the 2 connectors.

  10. INSTALL CONSOLE BOX (for RHD)


    1. A01NDV8E01
      Text in Illustration
      *1 Clamp
      *2 Guide

      Engage the 3 guides as shown in the illustration.

    2. Engage the 2 clamps.

    3. Install the 2 clips.

    4. A01NCM1

      Install the console box with the 5 screws <D>.

  11. INSTALL CONSOLE BOX (for LHD)


    1. A01NF55E01
      Text in Illustration
      *1 Clamp
      *2 Guide

      Engage the 3 guides as shown in the illustration.

    2. Engage the 2 clamps.

    3. Install the 3 clips.

    4. A01NDJA

      Install the console box with the 5 screws <D>.

  12. INSTALL RADIO RECEIVER ASSEMBLY WITH REGISTER


    1. Connect each connector.

    2. A01NCUB

      Engage the 9 clips.

    3. Install the radio receiver assembly with register with the 4 bolts.

      Torque:
      4.9 N*m  { 50 kgf*cm, 43 in.*lbf }

  13. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL


    1. A01NF11

      Engage the 7 clips to install the lower instrument panel finish panel as shown in the illustration.

  14. INSTALL INSTRUMENT PANEL FINISH PANEL


    1. A01ND4S

      Engage the 2 guides, claw and 2 clips to install the instrument panel finish panel as shown in the illustration.

  15. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. Connect each connector.

    2. A01NG78

      Engage the 8 clips and 2 guides.

    3. Install the lower instrument panel finish panel sub-assembly with the 2 screws <D>.

    4. A01NE1K

      Engage the 2 claws to close the cover as shown in the illustration.

  16. INSTALL NO. 1 SWITCH HOLE BASE


    1. Connect each connector.

    2. A01NFF7

      Engage the 4 claws and 2 guides to install the No. 1 switch hole base.

  17. INSTALL INSTRUMENT PANEL GARNISH LH


    1. A01NH3A

      Engage the 6 clips to install the instrument panel garnish LH.

  18. INSTALL REAR CONSOLE BOX ASSEMBLY


    1. A01ND4Q

      Engage the 8 guides as shown in the illustration.

    2. A01NEDEE01
      Text in Illustration
      *1 Screw
      *2 Bolt

      Install the rear console box assembly with the 2 screws and 4 bolts.

    3. Connect each connector.

  19. INSTALL MULTI-MEDIA INTERFACE ECU ASSEMBLY


    1. Connect the connector.

    2. A01NG12

      Engage the clip and guide.

    3. Install the multi-media interface ECU assembly with the 2 bolts.

      Torque:
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

  20. INSTALL CONSOLE REAR END PANEL SUB-ASSEMBLY


    1. A01NGOF

      w/o Rear Seat Entertainment System:


      1. Engage the 4 claws and 6 clips to install the console rear end panel sub-assembly.

    2. w/ Rear Seat Entertainment System:


      1. Connect each connector.

      2. Engage the 4 claws and 6 clips to install the console rear end panel sub-assembly.

  21. INSTALL NO. 2 CONSOLE BOX DUCT


    1. A01NH7K

      Install the No. 2 console box duct with the 2 screws.

  22. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. Engage the clamp.

    2. Connect each connector.

    3. A01NEE4

      Engage the 3 claws and 3 clips.

    4. w/o Seat Heater System:


      1. Connect the connector to the console box hole cover.

    5. A01NDQX

      w/ Seat Heater System:


      1. Engage the 4 claws to install the seat heater switch assembly.

      2. Connect the connector.

    6. A01NHPA

      Engage the 4 claws and 4 clips to install the upper console panel sub-assembly.

  23. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A01NH7J

      Turn the shift lever knob sub-assembly clockwise to install the shift lever knob sub-assembly.

  24. INSERT MAP DISC

  25. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  26. INSTALL REAR DECK FLOOR BOX


    1. A01NDSY

      Install the rear deck floor box with the 3 clips.

  27. INSPECT SHIFT LEVER POSITION


    1. When moving the shift lever from P to R with the power switch on (IG) and the brake pedal depressed, make sure that the shift lever moves smoothly and correctly into position.

    2. Turn the power switch on (READY) and make sure that the vehicle moves forward when moving the shift lever from N to D and moves rearward when moving the shift lever to R.

      If the operation cannot be performed as specified, inspect the shift lever position sensor and check the shift lever assembly installation condition.

  28. ADJUST SHIFT LEVER POSITION


    1. Apply the parking brake and move the shift lever to N.

      Note

      Check that the control shaft lever and the shift lever are in neutral.

    2. Remove the No. 1 engine under cover.

    3. A01NDL2

      Remove the nut from the control shaft lever.

    4. Using a screwdriver, disengage the 4 claws and disconnect the control cable with clip from the control cable bracket.

    5. Remove the clip.

    6. Turn back the boot.

    7. A01NGY7E01
      Text in Illustration
      *1 Slider
      *2 Lock Piece

      Slide the slider of the transmission control cable in the direction indicated by the arrow and pull the lock piece outward.

    8. Install a new clip to the control cable bracket.

    9. A01NFU7E03
      Text in Illustration
      *1 Claw A
      *2 Claw B
      *3 Control Cable

      Install the control cable to the control cable bracket.

      Note


      • Make sure that the claws A on the clip are securely fit into the bracket holes.

      • Make sure that the cable is securely installed inside of the claws B of the clip.

    10. A01NHPIE02
      Text in Illustration
      *1 Lock Piece

      Connect the transmission control cable to the control shaft lever with the nut.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

      Note

      Check that the lock piece is pulled up.

    11. A01NEF7E01
      Text in Illustration
      *1 Lock Piece

      Push the lock piece into the adjuster case.

      Note


      • Check that the shift lever position sensor and the shift lever are in neutral.

      • Securely push in the lock piece until the slider lock is engaged.

    12. Refit the boot.

    13. After adjusting the shift lever position, check the operation and function of the shift lever. If there is a problem, adjust the position again.

    14. Install the No. 1 engine under cover.

  29. INSPECT SUSPENSION CONTROL SYSTEM


    1. Inspect the suspension control system Click here.

  30. INSPECT SRS WARNING LIGHT


    1. Inspect the SRS warning light Click here.