NAVIGATION SYSTEM (for DVD) Display does not Dim when Light Control Switch is Turned ON

DESCRIPTION

When the navigation system is activated with the light control switch in the tail or head position, before AVC-LAN communication is established, the multi-display assembly dims the display according to the illumination signal received via a direct line.

After AVC-LAN communication is established, the multi-display assembly dims the display according to a dimmer signal sent via AVC-LAN communication.

The display and navigation module display switches between the daytime screen and night screen on the multi-display according to the illumination signal input.

WIRING DIAGRAM

A01NFPME02

INSPECTION PROCEDURE

PROCEDURE


  1. CONFIRM SYMPTOMS


    1. Check the symptoms that occur by viewing the display.

      Result
      Result Proceed to
      There is a delay until the display dims after the navigation system is activated with the light control switch in the tail or head position. A
      The display dims for a moment and then becomes bright after the navigation system is activated with the light control switch in the tail or head position. B
      When the light control switch is set to the tail or head position, the display dims but does not switch to the night screen. B
      When the light control switch is set to the tail or head position, the display neither dims nor switches to the night screen. C

      Tech Tips


      • When the navigation system is activated with the light control switch in the tail or head position, before AVC-LAN communication is established, the multi-display assembly dims the display according to the illumination signal received via a direct line.

      • After AVC-LAN communication is established, the multi-display assembly dims the display according to a dimmer signal sent via AVC-LAN communication.

      • The display and navigation module display switches between the daytime screen and night screen on the multi-display according to the illumination signal input.


    B
    C
    A
  2. CHECK HARNESS AND CONNECTOR (BATTERY - MULTI-DISPLAY ASSEMBLY)


    1. A01NFN7E10
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Multi-display Assembly)

      Disconnect the multi-display assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G2-13 (GND1) - Body ground Always Below 1 Ω
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      G2-2 (ILL) - G2-13 (GND1) Light control switch in tail or head 11 to 14 V

    NG
    OK
  3. CHECK IMAGE QUALITY SETTING


    1. A01NGP0

      Display the "Display" screen.

    2. Turn the light control switch to the tail position.

    3. Check if "Day Mode" on the display adjustment is on.

      OK
      "Day Mode" is on.

    NG
    OK
  4. CHECK VEHICLE SIGNAL (OPERATION CHECK)


    1. A01ND8F

      Display the "Vehicle Signal Check Mode" screen Click here.

    2. Check that the display changes between ON and OFF according to the light control switch operation.

      OK
      Light Control Switch Display
      tail or on ON
      off OFF

      Tech Tips

      The display is updated once per second. It is normal for the display to lag behind the actual switch operation.


    NG
    OK
  5. CHECK HARNESS AND CONNECTOR (BATTERY - DISPLAY AND NAVIGATION MODULE DISPLAY)


    1. A01NCTPE56
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Display and Navigation Module Display)

      Disconnect the display and navigation module display connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G4-10 (GND1) - Body ground Always Below 1 Ω
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      G4-12 (ILL+) - Body ground Light control switch in tail or head 11 to 14 V

    NG
    OK