NAVIGATION SYSTEM (for DVD), Diagnostic DTC:B15D0

DTC Code DTC Name
B15D0 MOST Communication Malfunction

DESCRIPTION

This DTC is stored when the MOST network cannot be established after the master unit is activated.

Tech Tips


  • If a short occurs in a speaker circuit, the sound from the corresponding speaker will be low or almost impossible to hear. If the volume is turned up in this situation, to prevent excessive current flow due to the short circuit, the stereo component amplifier assembly stops operating when its output exceeds a certain level. When the operation of the stereo component amplifier assembly stops, the navigation system will not function normally. This is because MOST communication will stop due to the shut down of the amplifier causing an error in the MOST network. The stereo component amplifier assembly will start operating again when the power switch is turned off and back on (ACC) again. However, the amplifier will stop operating again if its output exceeds a certain level. (for 15 speakers)

  • When the stereo component amplifier assembly stops operating and a malfunction occurs in the navigation system due to a short in a speaker circuit, this DTC will be stored. (for 15 speakers)

DTC No. DTC Detection Condition Trouble Area
B15D0 MOST network cannot be established.

  • Speaker circuit (for 15 speakers)

  • MOST line check

  • MOST communication line connector

  • Wire harness or connector

  • MOST communication line

  • Remote touch

  • Radio receiver assembly

  • Display and navigation module display

  • Stereo component amplifier assembly

Tech Tips


  • MOST network cannot be established.

  • Errors may occur in MOST communication between devices due to problems such as electrical noise.

WIRING DIAGRAM

A01NGR2E02

INSPECTION PROCEDURE

PROCEDURE


  1. CONFIRM MODEL


    1. Choose the model to be inspected.

      Result
      Model Proceed to
      for 15 speakers A
      except 15 speakers B

    B

    CHECK MOST LINE CHECK Click here

    A

  2. CONFIRM SYMPTOMS


    1. Power switch off.

    2. Turn the power switch on (ACC) and check if the audio system activates and if the speakers operate.

      Tech Tips


      • Choose a source such as radio so that sound can be output from the speakers.

      • If sound from the speakers is low, turn up the volume.

      Result
      Model Proceed to
      The audio system activates when the power switch is turned on (ACC) but the sound stops being output when the amplifier output exceeds a certain level. A
      Even after the power switch is turned on (ACC), the audio system does not activate and sound is not output from the speakers. B

      Tech Tips


      • If a short occurs in a speaker circuit, the sound from the corresponding speaker will be low or almost impossible to hear. If the volume is turned up in this situation, to prevent excessive current flow due to the short circuit, the stereo component amplifier assembly stops operating when its output exceeds a certain level. When the operation of the stereo component amplifier assembly stops, the navigation system will not function normally. This is because MOST communication will stop due to the shut down of the amplifier causing an error in the MOST network. The stereo component amplifier assembly will start operating again when the power switch is turned off and back on (ACC) again. However, the amplifier will stop operating again if its output exceeds a certain level.

      • When the stereo component amplifier assembly stops operating and a malfunction occurs in the navigation system due to a short in a speaker circuit, this DTC will be stored. In this case, check each speaker circuit and repair or replace malfunctioning parts, and then recheck for DTCs.


    B

    CHECK MOST LINE CHECK Click here

    A

    GO TO AUDIO AND VISUAL SYSTEM (w/ Navigation System) Click here

  3. CHECK MOST LINE CHECK


    1. A01NH23E01
      Text in Illustration
      *1 Node position number for devices that use MOST communication
      *2 Device Name
      *3 Result

      Display the "MOST Line Check" screen Click here.


      1. Check the result on the "MOST Line Check" screen.

        Result
        Result Proceed to
        "NCON" is displayed for "AMP". A
        "NCON" is displayed for "R-TOUCH". B
        "NCON" is displayed for "AUDIO". C
        "OK" is displayed for all items. D

        Tech Tips


        • When "NCON" is displayed for more than 1 item, proceed to the step for the device that has the smallest node position number.

        • The "MOST Line Check" screen can be displayed only when DTC B15D0 is stored.


    B

    CHECK MOST COMMUNICATION CONNECTOR Click here

    C

    CHECK MOST COMMUNICATION CONNECTOR Click here

    D

    CHECK HARNESS AND CONNECTOR Click here

    A

  4. CHECK MOST COMMUNICATION CONNECTOR


    1. Check the MOST communication line connector.


      1. Check the MOST communication line connectors of the radio receiver assembly and stereo component amplifier assembly Click here.

    2. Display the "MOST Line Check" screen and check the result Click here.

      Result
      Result Proceed to
      "NCON" is displayed for "AMP". A
      The screen cannot be changed to the "MOST Line Check" screen. B

      Tech Tips

      When the malfunction in the MOST network is repaired, the screen cannot be changed to the "MOST Line Check" screen.


    B

    END

    A

  5. CHECK HARNESS AND CONNECTOR (WAKE UP SIGNAL)


    1. A01NHK0E11
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Stereo Component Amplifier Assembly)

      Disconnect the stereo component amplifier assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      O15-3 (WUI) - Body ground Power switch on (ACC) 4.5 V or higher

    NG

    CHECK HARNESS AND CONNECTOR Click here

    OK

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY Click here

  6. CHECK HARNESS AND CONNECTOR


    1. A01NHK0E11

      Disconnect the stereo component amplifier assembly connector.

    2. A01NCWRE16

      Disconnect the radio receiver assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O15-3 (WUI) - G12-26 (WUO) Always Below 1 Ω
      O15-3 (WUI) - Body ground Always 10 kΩ or higher
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Stereo Component Amplifier Assembly)
      *2

      Front view of wire harness connector

      (to Radio Receiver Assembly)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE RADIO RECEIVER ASSEMBLY Click here

  7. CHECK MOST COMMUNICATION CONNECTOR


    1. Check the MOST communication line connector.


      1. Check the MOST communication line connectors of the display and navigation module display and remote touch Click here.

    2. Display the "MOST Line Check" screen and check the result Click here.

      Result
      Result Proceed to
      "NCON" is displayed for "R-TOUCH". A
      The screen cannot be changed to the "MOST Line Check" screen. B

      Tech Tips

      When the malfunction in the MOST network is repaired, the screen cannot be changed to the "MOST Line Check" screen.


    B

    END

    A

  8. CHECK HARNESS AND CONNECTOR (WAKE UP SIGNAL)


    1. A01NFJ2E11
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Remote Touch)

      Disconnect the remote touch connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      G14-8 (WUI) - Body ground Power switch on (ACC) 4.5 V or higher

    NG

    CHECK HARNESS AND CONNECTOR Click here

    OK

    REPLACE REMOTE TOUCH (REMOTE OPERATION BOARD) Click here

  9. CHECK HARNESS AND CONNECTOR


    1. A01NFJ2E11

      Disconnect the remote touch connector.

    2. A01NHO9E09

      Disconnect the display and navigation module display connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G14-8 (WUI) - G6-8 (WUO) Always Below 1 Ω
      G14-8 (WUI) - Body ground Always 10 kΩ or higher
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Remote Touch)
      *2

      Front view of wire harness connector

      (to Display and Navigation Module Display)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE DISPLAY AND NAVIGATION MODULE DISPLAY Click here

  10. CHECK MOST COMMUNICATION CONNECTOR


    1. Check the MOST communication line connector.


      1. Check the MOST communication line connectors of the radio receiver assembly and remote touch Click here.

    2. Display the "MOST Line Check" screen and check the result Click here.

      Result
      Result Proceed to
      "NCON" is displayed for "AUDIO". A
      The screen cannot be changed to the "MOST Line Check" screen. B

      Tech Tips

      When the malfunction in the MOST network is repaired, the screen cannot be changed to the "MOST Line Check" screen.


    B

    END

    A

  11. CHECK HARNESS AND CONNECTOR (WAKE UP SIGNAL)


    1. A01NCWRE17
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Radio Receiver Assembly)

      Disconnect the radio receiver assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      G12-12 (WUI) - Body ground Power switch on (ACC) 4.5 V or higher

    NG

    CHECK HARNESS AND CONNECTOR Click here

    OK

    REPLACE RADIO RECEIVER ASSEMBLY Click here

  12. CHECK HARNESS AND CONNECTOR


    1. A01NCWRE17

      Disconnect the radio receiver assembly connector.

    2. A01NFJ2E12

      Disconnect the remote touch connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G12-12 (WUI) - G14-4 (WUO) Always Below 1 Ω
      G12-12 (WUI) - Body ground Always 10 kΩ or higher
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Radio Receiver Assembly)
      *2

      Front view of wire harness connector

      (to Remote Touch)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE REMOTE TOUCH (REMOTE OPERATION BOARD) Click here

  13. CHECK HARNESS AND CONNECTOR


    1. A01NHO9E10

      Disconnect the display and navigation module display connector.

    2. A01NFJ2E13

      Disconnect the remote touch connector.

    3. A01NCWRE18

      Disconnect the radio receiver assembly connector.

    4. A01NHK0E12

      Disconnect the stereo component amplifier assembly connector.

    5. Measure the resistance between the display and navigation module display and stereo component amplifier assembly according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G6-1 (MI+) - O15-6 (MO+) Always Below 1 Ω
      G6-5 (MI-) - O15-12 (MO-) Always Below 1 Ω
      G6-2 (SLDI) - O15-11 (SLDO) Always Below 1 Ω
      G6-1 (MI+) - Body ground Always 10 kΩ or higher
      G6-5 (MI-) - Body ground Always 10 kΩ or higher
      G6-2 (SLDI) - Body ground Always 10 kΩ or higher

    6. Measure the resistance between the display and navigation module display and remote touch according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G6-3 (MO+) - G14-6 (MI+) Always Below 1 Ω
      G6-7 (MO-) - G14-5 (MI-) Always Below 1 Ω
      G6-6 (SLDO) - G14-7 (SLDI) Always Below 1 Ω
      G6-3 (MO+) - Body ground Always 10 kΩ or higher
      G6-7 (MO-) - Body ground Always 10 kΩ or higher
      G6-6 (SLDO) - Body ground Always 10 kΩ or higher

    7. Measure the resistance between the remote touch and radio receiver assembly according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G14-1 (MO+) - G12-9 (MI+) Always Below 1 Ω
      G14-2 (MO-) - G12-23 (MI-) Always Below 1 Ω
      G14-3 (SLDO) - G12-10 (SLDI) Always Below 1 Ω
      G14-1 (MO+) - Body ground Always 10 kΩ or higher
      G14-2 (MO-) - Body ground Always 10 kΩ or higher
      G14-3 (SLDO) - Body ground Always 10 kΩ or higher

    8. Measure the resistance between the radio receiver assembly and stereo component amplifier assembly according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G12-11 (MO+) - O15-4 (MI+) Always Below 1 Ω
      G12-25 (MO-) - O15-10 (MI-) Always Below 1 Ω
      G12-24 (SLDI) - O15-5 (SLDI) Always Below 1 Ω
      G12-11 (MO+) - Body ground Always 10 kΩ or higher
      G12-25 (MO-) - Body ground Always 10 kΩ or higher
      G12-24 (SLDI) - Body ground Always 10 kΩ or higher
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Display and Navigation Module Display)
      *2

      Front view of wire harness connector

      (to Remote Touch)
      *3

      Front view of wire harness connector

      (to Radio Receiver Assembly)
      *4

      Front view of wire harness connector

      (to Stereo Component Amplifier Assembly)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  14. CHECK DTC


    1. Clear the DTCs Click here.

    2. Recheck for DTCs and check if the same DTC is output again.

      OK
      No DTCs are output.

    NG

    REPLACE DISPLAY AND NAVIGATION MODULE DISPLAY Click here

    OK

    USE SIMULATION METHOD TO CHECK Click here