POWER WINDOW REGULATOR MOTOR (for Front Door) INSTALLATION

Tech Tips

Use the same procedure for the RH side and LH side.
The procedure listed below is for the LH side.

INSTALL FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY
Note

The regulator arm must be below the intermediate position when installing the front power window regulator motor assembly.
1. Using a T25 "TORX" driver, install the front power window regulator motor assembly with the 3 screws.
  
  Torque:
  
  5.4 N*m { 55 kgf*cm, 48 in.*lbf }
  
  Tech Tips
  
  A new front window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.
INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY
1. Apply MP grease to the sliding parts of the front door window regulator assembly.
2. Install the temporary bolt to the front door window regulator assembly.
3. Text in Illustration
  
  *1 Temporary Bolt
  
  Temporarily install the front door window regulator assembly.
4. Tighten the temporary bolt and 5 bolts to install the front door window regulator assembly.
  
  Tech Tips
  
  Tighten the bolts in the order shown in the illustration.
  
  Torque:
  
  8.0 N*m { 82 kgf*cm, 71 in.*lbf }
5. Connect the connector.

Text in Illustration
*1	Temporary Bolt

INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

Connect the cable to the negative (-) battery terminal.

Connect the power window regulator master switch assembly and move the front door glass subassembly so that the door glass bolts can be seen.

w/ Navigation System for HDD:

Note

After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal
Specification	Waiting Time
w/o Telematics transceiver	60 sec.
w/ Telematics transceiver	120 sec.

Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system Click here.
Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated by the arrows in the order shown in the illustration.
Install the front door glass sub-assembly with the 2 bolts.

Torque:

5.5 N*m { 56 kgf*cm, 49 in.*lbf }

Tech Tips

Tighten the bolts in the order shown in the illustration.

INSTALL FRONT DOOR SERVICE HOLE COVER
1. Apply butyl tape to the front door panel.
2. Text in Illustration
  
  *1 Reference Point
  
  Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.
3. Attach the front door service hole cover according to the reference points on the front door panel.
  
  Note
  
  Securely install the front door service hole cover preventing wrinkles and air bubbles.
4. Connect the connector.
INSTALL NO. 1 FRONT DOOR TRIM BRACKET
1. Install the 2 bolts and No. 1 front door trim bracket.
INSTALL FRONT NO. 3 SPEAKER ASSEMBLY
1. Engage the clip and temporarily install the front No. 3 speaker assembly.
2. Install the front No. 3 speaker assembly with the 2 screws.
3. Connect the connector.
INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP
1. Engage the 4 claws and install the front door inner glass weatherstrip as shown in the illustration.
INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY
1. Install a new front door trim board retainer (green).
2. Connect the front door lock remote control cable assembly and front door inside locking cable assembly.
3. Connect each connector.
4. Engage the front door trim board sub-assembly with the 4 claws of the front door inner glass weatherstrip as shown in the illustration.
5. Text in Illustration
  
  *1 Front Door Trim Board Retainer
  
  Engage the 10 clips, front door trim board retainer and install the front door trim board sub-assembly.
6. Install the 3 screws.
  
  Torque:
  
  (A)
  
  3.5 N*m { 36 kgf*cm, 31 in.*lbf }
INSTALL NO. 1 FRONT DOOR STIFFENER CUSHION
1. Install the No. 1 front door stiffener cushion with the screw.
INSTALL COURTESY LIGHT ASSEMBLY
1. Connect the connector.
2. Engage the claw to install the courtesy light assembly.
INSTALL DOOR ARMREST COVER
1. Install the door armrest cover.
INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)
1. Connect the connector.
2. Engage the 2 clips and 5 claws, and install the power window regulator master switch assembly with front door armrest base panel.
INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)
1. Connect the connector.
2. Engage the 2 clips and 5 claws, and install the power window regulator switch assembly with front door armrest base panel.
INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG
1. Engage the 3 claws and install the front door inside handle bezel plug.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
INSTALL REAR DECK FLOOR BOX
1. Install the rear deck floor box with the 3 clips.
INITIALIZE POWER WINDOW CONTROL SYSTEM

Click here