POWER WINDOW REGULATOR MOTOR (for Front Door) INSPECTION


  1. INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


    1. A01NG3LE03
      Text in Illustration
      *1

      Component without harness connected

      (Front Power Window Regulator Motor Assembly LH)

      Apply positive (+) battery voltage to connector terminal 2 (B).

      Note

      Do not apply positive (+) battery voltage to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.

    2. Connect a ground lead to connector terminals 1 (E) and 7 (DWN1) or 10 (UP1).

    3. Check that the motor gear rotates smoothly as follows:

      OK
      Measurement Condition Specified Condition

      1. Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (E), and keep them connected for 3 seconds or more.

      2. With terminals 2 (B) and 1 (E) connected, connect a negative (-) battery lead to terminal 10 (UP1).

      3. Disconnect and reconnect the negative (-) battery lead to terminal 10 (UP1) within 1 second.

      		 Motor gear rotates clockwise

      1. Connect the positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (E), and keep them connected for 3 seconds or more.

      2. With terminals 2 (B) and 1 (E) connected, connect a negative (-) battery lead to terminal 7 (DWN1).

      3. Disconnect and reconnect the negative (-) battery lead to terminal 7 (DWN1) within 1 second.

      		 Motor gear rotates counterclockwise

      • If the result is not as specified, replace the front power window regulator motor assembly LH.

      CAUTION:

      Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.

  2. INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH


    1. A01NHMGE02
      Text in Illustration
      *1

      Component without harness connected

      (Front Power Window Regulator Motor Assembly RH)

      Apply positive (+) battery voltage to connector terminal 2 (B).

      Note

      Do not apply positive (+) battery voltage to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.

    2. Connect a ground lead to connector terminals 1 (E) and 7 (DWN1) or 10 (UP1).

    3. Check that the motor gear rotates smoothly as follows:

      OK
      Measurement Condition Specified Condition

      1. Connect the positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (E), and keep them connected for 3 seconds or more.

      2. With terminals 2 (B) and 1 (E) connected, connect a negative (-) battery lead to terminal 10 (UP1).

      3. Disconnect and reconnect the negative (-) battery lead to terminal 10 (UP1) within 1 second.

      		 Motor gear rotates counterclockwise

      1. Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (E), and keep them connected for 3 seconds or more.

      2. With terminals 2 (B) and 1 (E) connected, connect a negative (-) battery lead to terminal 7 (DWN1).

      3. Disconnect and reconnect the negative (-) battery lead to terminal 7 (DWN1) within 1 second.

      		 Motor gear rotates clockwise

      • If the result is not as specified, replace the front power window regulator motor assembly RH.

      CAUTION:

      Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.