POWER WINDOW REGULATOR MOTOR (for Front Door) REMOVAL

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.


  1. PRECAUTION (w/ Navigation System for HDD)

    Note

    After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

    Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal
    Specification Waiting Time
    w/o Telematics transceiver 60 sec.
    w/ Telematics transceiver 120 sec.

  2. REMOVE REAR DECK FLOOR BOX


    1. A01NDSY

      Remove the 3 clips and the rear deck floor box.

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. A01NCWL

      Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel plug as shown in the illustration.

  5. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    1. A01NHP9

      Using a moulding remover, disengage the 2 clips and 5 claws as shown in the illustration.

    2. Disconnect the connector and remove the power window regulator master switch assembly with front door armrest base panel.

  6. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    1. A01NFG7

      Using a moulding remover, disengage the 2 clips and 5 claws.

    2. Disconnect the connector and remove the power window regulator switch assembly with front door armrest base panel.

  7. REMOVE DOOR ARMREST COVER


    1. A01NHCO

      Remove the door armrest cover.

  8. REMOVE COURTESY LIGHT ASSEMBLY


    1. A01NHVPE01

      Using a screwdriver wrapped with protective tape, disengage the claw.

    2. Disconnect the connector and remove the courtesy light assembly.

  9. REMOVE NO. 1 FRONT DOOR STIFFENER CUSHION


    1. A01NCRL

      Remove the screw and No. 1 front door stiffener cushion.

  10. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. A01NFFCE02

      Remove the 3 screws.

    2. Using a clip remover, disengage the 10 clips and front door trim board retainer.

      Text in Illustration
      *1 Front Door Trim Board Retainer
    3. A01NFAL

      Pull out the front door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.

    4. Raise the front door trim board sub-assembly to disengage the 4 claws and remove the front door trim board sub-assembly together with the front door inner glass weatherstrip.

    5. Disconnect each connector.

    6. A01NFHV

      Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.

    7. Remove the front door trim board retainer (green) from the front door trim board sub-assembly.

  11. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP


    1. A01NFKX

      Using a moulding remover, disengage the 4 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.

  12. REMOVE FRONT NO. 3 SPEAKER ASSEMBLY


    1. A01NEQH

      Disconnect the connector.

    2. Remove the 2 screws.

    3. Disengage the clip and remove the front No. 3 speaker assembly.

  13. REMOVE NO. 1 FRONT DOOR TRIM BRACKET


    1. A01NE1N

      Remove the 2 screws and No. 1 front door trim bracket.

  14. REMOVE FRONT DOOR SERVICE HOLE COVER


    1. A01NGSO

      Disconnect the connector.

    2. Remove the front door service hole cover.

      Tech Tips

      Remove any remaining butyl tape from the door.

  15. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


    1. Connect the cable to the negative (-) battery terminal.

    2. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.


      1. w/ Navigation System for HDD:

        Note

        After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

        Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal
        Specification Waiting Time
        w/o Telematics transceiver 60 sec.
        w/ Telematics transceiver 120 sec.

    3. Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system Click here.

    4. A01NHW3

      Remove the 2 bolts.

      Note

      After the bolts are removed, do not allow the door glass to fall.

    5. A01NDL4E01

      Remove the front door glass sub-assembly as indicated by the arrows in the order shown in the illustration.

      Note

      Do not damage the door glass.

  16. REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY


    1. A01NGEIE01
      Text in Illustration
      *1 Temporary Bolt

      Disconnect the connector.

    2. Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator may fall and cause damage.

    3. Remove the 5 bolts.

    4. Remove the front door window regulator assembly.

    5. Remove the temporary bolt from the front door window regulator assembly.

  17. REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY


    1. A01NEXC

      Using a T25 "TORX" driver, remove the 3 screws and the front power window regulator motor assembly.