POWER WINDOW CONTROL SYSTEM OPERATION CHECK

CHECK WINDOW LOCK SWITCH

Tech Tips

Before performing the window lock switch operation check, make sure that the window lock switch is off (the switch is not pushed in).

When the window lock switch of the multiplex network master switch assembly is pushed in, the LED on the switch will illuminate. Check that the power window switch operation indicators for all of switches other than those on the multiplex network master switch are off and that the front passenger and rear windows are disabled.

Tech Tips

Even when the window lock switch of the multiplex network master switch assembly is pushed in, remote manual up and down and auto up and down functions can be operated.

When the window lock switch is pushed in again, the LED on the switch will go off. Check that all of the power window switch operation indicators illuminate and that the front passenger and rear windows can be operated normally.

CHECK MANUAL UP / DOWN FUNCTION

Check that the driver door power window operates as follows:

OK
Condition	Master Switch	Switch Operation	Power Window
Power switch on (IG)	Driver side	Pulled halfway up	UP (Closes)
Power switch on (IG)	Driver side	Pushed halfway down	DOWN (Opens)

Check that the front passenger side window and rear power windows operate as follows:

OK
Condition	Regulator Switch	Switch Operation	Power Window
Power switch on (IG) Window lock switch off	Front passenger side	Pulled halfway up	UP (Closes)
	Front passenger side	Pushed halfway down	DOWN (Opens)
	Rear LH side	Pulled halfway up	UP (Closes)
	Rear LH side	Pushed halfway down	DOWN (Opens)
	Rear RH side	Pulled halfway up	UP (Closes)
	Rear RH side	Pushed halfway down	DOWN (Opens)

CHECK AUTO UP / DOWN FUNCTION

Check that the driver door power window operates as follows:

OK
Condition	Master Switch	Switch Operation	Power Window
Power switch on (IG)	Driver side	Pulled up (One touch operation)	AUTO UP (Closes)
Power switch on (IG)	Driver side	Pushed down (One touch operation)	AUTO DOWN (Opens)

Check that the front passenger side window and rear power windows operate as follows:

OK
Condition	Regulator Switch	Switch Operation	Power Window
Power switch on (IG) Window lock switch off	Front passenger side	Pulled up (One touch operation)	AUTO UP (Closes)
	Front passenger side	Pushed down (One touch operation)	AUTO DOWN (Opens)
	Rear LH side	Pulled up (One touch operation)	AUTO UP (Closes)
	Rear LH side	Pushed down (One touch operation)	AUTO DOWN (Opens)
	Rear RH side	Pulled up (One touch operation)	AUTO UP (Closes)
	Rear RH side	Pushed down (One touch operation)	AUTO DOWN (Opens)

CHECK REMOTE MANUAL UP / DOWN FUNCTION

Check that the front passenger side window and rear power windows operate as follows:

OK
Condition	Master Switch	Switch Operation	Power Window
Power switch on (IG)	Front passenger side	Pulled halfway up	UP (Closes)
	Front passenger side	Pushed halfway down	DOWN (Opens)
	Rear LH side	Pulled halfway up	UP (Closes)
	Rear LH side	Pushed halfway down	DOWN (Opens)
	Rear RH side	Pulled halfway up	UP (Closes)
	Rear RH side	Pushed halfway down	DOWN (Opens)

CHECK REMOTE AUTO UP / DOWN FUNCTION

Check that the front passenger side window and rear power windows operate as follows:

OK
Condition	Master Switch	Switch Operation	Power Window
Power switch on (IG)	Front passenger side	Pulled up (One touch operation)	AUTO UP (Closes)
	Front passenger side	Pushed down (One touch operation)	AUTO DOWN (Opens)
	Rear LH side	Pulled up (One touch operation)	AUTO UP (Closes)
	Rear LH side	Pushed down (One touch operation)	AUTO DOWN (Opens)
	Rear RH side	Pulled up (One touch operation)	AUTO UP (Closes)
	Rear RH side	Pushed down (One touch operation)	AUTO DOWN (Opens)

CHECK POWER WINDOW OPERATION FUNCTION AFTER POWER SWITCH IS TURNED OFF

Check that all the power windows can be operated with the multiplex network master switch assembly and power window regulator switch assemblies (for front passenger side, rear LH and RH sides) after the power switch is turned off.

Tech Tips

If the window lock switch is on, the windows cannot be operated using the power window regulator switch assemblies (for front passenger, rear LH and RH sides). Therefore, turn the window lock switch off before checking the window operation.
Check that the key-off operation function does not operate after the driver door or front passenger door is opened.

Tech Tips

Even if the driver door or front passenger door is opened during automatic window operation while the key-off operation function is on, the window will continue operating.
Check that all the power windows cannot be operated after more than approximately 45 seconds have elapsed since the power switch was turned off.

CHECK KEY-LINKED FUNCTION USING DRIVER SIDE DOOR KEY CYLINDER

Check that all power windows operate as follows:

OK
Condition	Door Key Cylinder Operation	Power Window
No key is inside vehicle, and all doors are closed	Held (LOCK) for more than 1.5 seconds	UP (Closes)
No key is inside vehicle, and all doors are closed	Returned to neutral position	STOP
No key is inside vehicle, and all doors are closed	Held (UNLOCK) for more than 1.5 seconds	DOWN (Opens)
No key is inside vehicle, and all doors are closed	Returned to neutral position	STOP

CHECK WIRELESS TRANSMITTER-LINKED FUNCTION

Check that all power windows operate as follows when operating the transmitter:

OK
Condition	Transmitter Operation	Power Window
No key is inside vehicle, and all doors are closed and locked	UNLOCK switch pressed for more than 3.0 seconds	DOWN (Opens)
No key is inside vehicle, and all doors are closed and locked	UNLOCK switch released	STOP
No key is inside vehicle, and all doors are closed and locked	LOCK switch pressed for more than 3.0 seconds	UP (Closes)
No key is inside vehicle, and all doors are closed and locked	LOCK switch released	STOP

CHECK SUGGEST MODE FUNCTION

Tech Tips

If the window lock switch is on, suggest mode operation is not available. Therefore, be sure to confirm that the switch is off before performing the following inspection.
If all windows are fully closed, suggest mode operation is not available.
If the operation conditions for the key-off operation function are not met, suggest mode operation is not available.

When any window is open after the power switch is turned off, check that "DO YOU WANT TO CLOSE ALL WINDOWS?" appears on the multi-information display in the combination meter assembly.
Select "YES" by operating the steering pad switch assembly (multi-information switch).
Check that the message changes to "SELECT START TO CLOSE WINDOWS".
Select "START" by operating the steering pad switch assembly (multi-information switch). Check that all open windows start closing automatically.
While the windows are closing, check that "PRESS ENTER TO STOP WINDOWS" appears on the display.

Tech Tips

If the ENTER switch on the steering pad switch assembly (multi-information switch) is pressed, the windows that are closing will stop, and the message "PRESS ENTER TO STOP WINDOWS" will disappear.

CHECK JAM PROTECTION FUNCTION

Check the basic function.

CAUTION:

Do not put your fingers between the door frame and door glass to check the jam protection function. Also, prevent any part of your body from being caught during inspection.

Tech Tips

The jam protection function is operative during both the auto up and manual up operations while the engine is running or the power switch is on (IG), and also 45 seconds have elapsed after the power switch is turned off.
1. Fully open the window.
2. Set a thick book wrapped with a piece of cloth near the window fully closed position.
3. Operate the auto up or manual up function to check that the power window goes down after the book is caught between the window and door frame, and stops when the opening reaches approximately 200 mm (7.87 in.).
  
  Tech Tips
  
  The power window moves down approximately 125 mm (4.93 in.). However, when the opening does not reach 200 mm (7.87 in.), the power window continues to go down until the opening reaches 200 mm (7.87 in.) or until approximately 5 seconds elapse.
4. While the power window is moving down, check that the door glass cannot be raised when the power window switch is used.

CHECK POWER WINDOW SWITCH LED ILLUMINATION

Check the LED illumination (multiplex network master switch assembly).
1. Check that the LEDs located on the multiplex network master switch assembly illuminate when the power switch is turned on (IG).
Check the LED illumination (power window regulator switch assembly (for front passenger side)).
1. Check that the LED located on the power window regulator switch assembly (for front passenger side) illuminates when the power switch is turned on (IG).
  
  Tech Tips
  
  If the window lock switch is on, the LED located on the power window regulator switch assembly (for front passenger side) does not illuminate. Therefore, turn the window lock switch off before checking the LED illumination.
Check the LED illumination (power window regulator switch assembly (for rear LH and RH)).
1. Check that the LED located on each power window regulator switch assembly (for rear LH and RH) illuminates when the power switch is turned on (IG).
  
  Tech Tips
  
  If the window lock switch is on, the LEDs located on the power window regulator switch assemblies (for rear LH and RH) do not illuminate. Therefore, turn the window lock switch off before checking the LED illumination.