ELECTRONICALLY CONTROLLED BRAKE SYSTEM, Diagnostic DTC:C1249/49

DTC Code DTC Name
C1249/49 Open in Stop Light Switch Circuit

DESCRIPTION

The skid control ECU inputs the stop light switch signal and detects the brake pedal operation status.

The skid control ECU has an open detection circuit, which outputs this DTC if it detects an open in the stop light input line or ground line of the stop light circuit with the stop light switch off (brake pedal not depressed).

DTC Code INF Code DTC Detection Condition Trouble Area
C1249/49 520 When IG2 terminal voltage is 9.5 V or more, an open stop light switch circuit continues for 10 seconds or more.

  • STOP fuse

  • Stop light switch

  • Stop light switch circuit

  • Skid control ECU

WIRING DIAGRAM

A01NFTTE02

INSPECTION PROCEDURE

Note

When replacing the skid control ECU, perform initialization and calibration of the linear solenoid valve Click here.

PROCEDURE


  1. CHECK STOP LIGHT OPERATION


    1. Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

      OK
      Condition Illumination Condition
      Brake pedal depressed ON
      Brake pedal released OFF

    NG

    INSPECT STOP FUSE Click here

    OK

  2. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Select the Data List on the intelligent tester Click here.

      ABS/VSC/TRC
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Stop Light SW Stop light switch / ON or OFF

      ON: Brake pedal depressed

      OFF: Brake pedal released

      		 -

    4. Check that the stop light switch display observed on the intelligent tester changes according to brake pedal operation.

      OK
      The intelligent tester displays ON or OFF according to brake pedal operation.

    NG

    CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - STOP LIGHT SWITCH) Click here

    OK

  3. RECONFIRM DTC


    1. Turn the power switch off.

    2. Clear the DTCs Click here.

    3. Turn the power switch on (READY).

    4. Depress the brake pedal several times to test the stop light circuit.

    5. Check if the same DTC is recorded Click here.

      Result
      Result Proceed to
      DTC (C1249/49) is not output A
      DTC (C1249/49) is output B

      Tech Tips

      If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step Click here.


    B

    REPLACE SKID CONTROL ECU Click here

    A

    CHECK FOR INTERMITTENT PROBLEMS Click here

  4. INSPECT STOP FUSE


    1. A01NFUNE06
      Text in Illustration
      *1 Engine Room Relay Block
      *2 STOP Fuse

      Remove the STOP fuse from the engine room relay block.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      STOP (7.5 A) fuse Always Below 1 Ω

    NG

    REPLACE STOP FUSE

    OK

  5. INSPECT STOP LIGHT SWITCH (POWER SOURCE TERMINAL)


    1. A01NFFLE24
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Stop Light Switch)

      Install the STOP fuse.

    2. Make sure that there is no looseness at the locking part and the connecting part of the connector.

    3. Disconnect the stop light switch connector.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A47-2 - Body ground Always 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

    OK

  6. INSPECT STOP LIGHT SWITCH


    1. A01NFS6E05

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      1 - 2 Switch pin free Below 1 Ω
      1 - 2 Switch pin pushed in 10 kΩ or higher

    NG

    REPLACE STOP LIGHT SWITCH Click here

    OK

  7. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - STOP LIGHT SWITCH)


    1. A01NCN6E02
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Skid Control ECU)
      *2

      Front view of wire harness connector

      (to Stop Light Switch)

      Make sure that there is no looseness at the locking part and the connecting part of the connector.

    2. Disconnect the skid control ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A91-16 (STP1) - A47-1 Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  8. RECONFIRM DTC


    1. Reconnect the skid control ECU connector and the stop light switch connector.

    2. Clear the DTCs Click here.

    3. Turn the power switch on (READY).

    4. Depress the brake pedal several times to test the stop light circuit.

    5. Check if the same DTC is recorded Click here.

      Result
      Result Proceed to
      DTC (C249/49) is not output A
      DTC (C1249/49) is output B

      Tech Tips

      If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step Click here.


    B

    REPLACE SKID CONTROL ECU Click here

    A

    INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT) Click here

  9. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - STOP LIGHT SWITCH)


    1. A01NCN6E02
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Skid Control ECU)
      *2

      Front view of wire harness connector

      (to Stop Light Switch)

      Turn the power switch off.

    2. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

    3. Disconnect the skid control ECU connector and the stop light switch connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A91-16 (STP1) - A47-1 Always Below 1 Ω

      Tech Tips

      If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step Click here.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE SKID CONTROL ECU Click here