REAR ACTIVE STABILIZER CONTROL ACTUATOR INSTALLATION


  1. INSTALL REAR STABILIZER BUSHING


    1. A01NHPLE01
      Text in Illustration
      *1 Stopper

      Install the 2 rear stabilizer bushings to the outside of the stoppers on the rear active stabilizer control actuator assembly.

  2. INSTALL REAR NO. 1 STABILIZER BAR BRACKET


    1. A01NHXPE01
      Text in Illustration
      *1 Identification Shape
      *2 Identification Mark

      Install the 2 rear No. 1 stabilizer bar brackets to the rear stabilizer bushings.

      Note


      • Ensure that the identification shape faces upward.

      • Ensure that the identification mark is on the right side of the vehicle.

  3. INSTALL REAR ACTIVE STABILIZER CONTROL ACTUATOR ASSEMBLY


    1. A01NDYEE01
      Text in Illustration
      *1 Identification Mark

      Install the rear active stabilizer control actuator assembly with 2 rear stabilizer bushings and 2 rear No. 1 stabilizer bar brackets with the 4 nuts.

      Torque:
      75 N*m  { 765 kgf*cm, 55 ft.*lbf }

      Note


      • Ensure that the identification mark is on the right side of the vehicle.

      • Take care not to damage the wire harness and connectors of the rear active stabilizer control actuator assembly.

      • Avoid any impact to the rear active stabilizer control actuator assembly.

      • Do not drop the rear active stabilizer control actuator assembly. If it is dropped, replace it with a new one.

    2. A01NH56E01

      Using the procedures below, connect the connector (A).


      1. Connect the connector (A).*1

      2. Rotate the lever in the direction of the arrow until a "click" sound is heard.*2

      3. Lock the lever's lock.*3

    3. Engage the 2 clamps and connect the connector (B).

  4. INSTALL NO. 2 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR


    1. A01NGGW

      Engage the 2 craws and install the No. 2 luggage compartment side cover protector.

    2. Install the 3 clips and 2 bolts.

    3. Install the 4 screws.

      Torque:
      7.5 N*m  { 77 kgf*cm, 66 in.*lbf }
    4. A01NGGR

      Install the 2 screws.

      Torque:
      7.5 N*m  { 77 kgf*cm, 66 in.*lbf }

    5. Install a new grommet.

  5. INSTALL REAR QUARTER PANEL MUDGUARD SUB-ASSEMBLY LH (w/ Rear Fender Mudguard)


    1. A01NDHL

      Using a 4 mm hexagon wrench, install the rear quarter panel mudguard sub-assembly with the 3 hexagon screws.

      Torque:
      7.5 N*m  { 77 kgf*cm, 66 in.*lbf }
    2. A01NFP7

      Install the 2 screws.

      Torque:
      7.5 N*m  { 77 kgf*cm, 66 in.*lbf }

  6. INSTALL REAR STABILIZER LINK SUB-ASSEMBLY


    1. Install the rear stabilizer link sub-assembly (LH Side).


      1. A01NFTZ

        Hold the rear lower stabilizer bracket between aluminium plates in a vise as shown in the illustration.

        Note

        Do not overtighten the vise.

      2. Install the rear stabilizer link sub-assembly to the rear lower stabilizer bracket as shown in the illustration.

        Torque:
        92 N*m  { 938 kgf*cm, 68 ft.*lbf }

        Tech Tips

        If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud bolt.

      3. A01NHUOE01

        Install the rear stabilizer link sub-assembly to the rear active stabilizer control actuator assembly with the nut (B).

        Torque:
        90 N*m  { 918 kgf*cm, 66 ft.*lbf }

        Tech Tips

        If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud bolt.

      4. Install the rear stabilizer link sub-assembly with rear lower stabilizer bracket to the rear No. 2 suspension arm assembly LH with the 2 nuts (A).

        Torque:
        82 N*m  { 836 kgf*cm, 60 ft.*lbf }

    2. Install the rear stabilizer link sub-assembly (RH Side).

      Tech Tips

      Perform the same procedure as the LH side.