SUSPENSION CONTROL ECU (for LHD) INSTALLATION


  1. INSTALL SUSPENSION CONTROL ECU


    1. A01NHIP

      Connect the 3 connectors.

    2. A01NHLC

      Install the suspension control ECU to the body with the 3 bolts.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note


      • Avoid any impact to the suspension control ECU.

      • Do not drop the ECU. If the ECU is dropped, replace it with a new one.

      • If the suspension control ECU is replaced with a new one, perform registration of vehicle identification information Click here.

  2. INSTALL SKID CONTROL ECU ASSEMBLY


    1. A01NDFA

      Connect the 4 connectors to the skid control ECU.

    2. Install the skid control ECU with the 2 bolts.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

  3. INSTALL ECU INTEGRATION BOX RH


    1. A01NE0U

      Install the ECU integration box RH with the 2 nuts and bolt.

    2. A01NEFY

      Install the No. 3 connector holder with the nut and claw.

    3. A01ND4D

      Connect each connector.

  4. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


    1. Connect each connector.

    2. A01NGIS

      Engage the claw, 4 clips and guide.

    3. A01NFHC

      Install the glove compartment door assembly with the 5 screws <F>.

  5. INSTALL FRONT PASSENGER SIDE KNEE AIRBAG ASSEMBLY


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01NHUG

      Connect the airbag connector to the front passenger side knee airbag assembly.

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.

    4. A01NFZX

      Temporarily install the front passenger side knee airbag assembly with the claw and 2 pins.

    5. Install the front passenger side knee airbag assembly with the 3 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note

      Confirm that the front passenger side knee airbag assembly is installed securely without any excessive gaps and is not protruding outward.

    6. A01NFX4E01
      Text in Illustration
      *1 Protective Tape

      Remove the protective tape.

  6. INSTALL INSTRUMENT PANEL GARNISH RH (w/o Airbag Cut Off Switch)

    Tech Tips

    Use the same procedure for the RH side and LH side.

  7. INSTALL INSTRUMENT PANEL GARNISH RH (w/ Airbag Cut Off Switch)


    1. Connect the connector.

    2. A01NGEE

      Engage the 6 clips to install the instrument panel garnish RH.

  8. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. Connect the connector.

    2. A01NH29

      Engage the 2 guides and 4 claw to install the No. 2 instrument panel under cover sub-assembly.

  9. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  10. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  11. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL


    1. A01NF11

      Engage the 7 clips to install the lower instrument panel finish panel as shown in the illustration.

  12. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. Engage the clamp.

    2. Connect each connector.

    3. A01NEE4

      Engage the 3 claws and 3 clips.

    4. w/o Seat Heater System:


      1. Connect the connector to the console box hole cover.

    5. A01NDQX

      w/ Seat Heater System:


      1. Engage the 4 claws to install the seat heater switch assembly.

      2. Connect the connector.

    6. A01NHPA

      Engage the 4 claws and 4 clips to install the upper console panel sub-assembly.

  13. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A01NH7J

      Turn the shift lever knob sub-assembly clockwise to install the shift lever knob sub-assembly.

  14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  15. INSTALL REAR DECK FLOOR BOX


    1. A01NDSY

      Install the rear deck floor box with the 3 clips.

  16. INSPECT SUSPENSION CONTROL SYSTEM

    Note

    If the suspension control ECU is replaced with a new one, perform registration of vehicle identification information.


    1. Inspect the suspension control system Click here.

  17. ADJUST VEHICLE HEIGHT

    Note

    If the suspension control ECU has been replaced, be sure to adjust the vehicle height.


    1. Adjust the vehicle height Click here.

  18. PERFORM INITIALIZATION


    1. Perform initialization Click here.

  19. CHECK SRS WARNING LIGHT


    1. Check the SRS warning light Click here.

  20. ADJUST HEADLIGHT ASSEMBLY (for HID Headlight)


    1. Adjust the headlight Click here.

  21. ADJUST HEADLIGHT ASSEMBLY (for LED Headlight)


    1. Adjust the headlight Click here.