REAR AXLE CARRIER (for 2WD) REMOVAL

Note

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1341, C1342, C1343 and/or C1344 may be stored. As there is no malfunction, clear the DTC(s).

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.


  1. REMOVE REAR WHEEL

  2. DRAIN BRAKE FLUID

    Note

    If brake fluid leaks onto any painted surface, immediately wash it off.

  3. REMOVE REAR SUSPENSION ARM COVER


    1. A01NFBI

      Remove the 2 bolts.

    2. Disengage the 2 guides and remove the rear suspension arm cover from the rear No. 2 suspension arm assembly.

  4. REMOVE REAR DISC BRAKE CALIPER ASSEMBLY


    1. A01NG3I

      Using a union nut wrench, disconnect the brake line from the rear flexible hose.

      Note


      • Do not bend or damage the brake line.

      • Do not allow any foreign matter such as dirt and dust to enter the brake line.

    2. Remove the clip and separate the rear flexible hose.

    3. A01NH1S

      Remove the bolt and separate the rear flexible hose from the rear upper control arm assembly.

    4. A01NHLR

      Remove the 2 bolts and rear disc brake caliper assembly with rear flexible hose.

  5. REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG


    1. Remove the parking brake shoe adjusting hole plug.

  6. REMOVE REAR DISC


    1. A01NFCBE01
      Text in Illustration
      *1 Matchmark

      Put matchmarks on the rear disc and the axle hub.

    2. A01ND9X

      Release the parking brake and remove the rear disc.

      Tech Tips

      If the disc can not be removed easily, use a screwdriver to turn the shoe adjuster as shown in the illustration in order to contract the parking brake shoes.

  7. SEPARATE REAR SPEED SENSOR WIRE


    1. A01NHMJ

      Remove the bolt and No. 1 bracket.

    2. A01NE3KE01

      Using a screwdriver, disconnect the connector from the rear speed sensor.

      Note

      Be careful not to damage the rear speed sensor.

  8. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY


    1. A01NGD7

      Remove the 4 bolts and the rear axle hub and bearing assembly from the rear axle carrier sub-assembly.

  9. LOOSEN PARKING BRAKE ASSEMBLY


    1. A01NG9Y

      Loosen the nut to separate the parking brake assembly after removing the rear trailing arm assembly.

  10. REMOVE REAR TRAILING ARM ASSEMBLY


    1. A01NFXT

      Remove the 2 bolts and separate the No. 3 parking brake cable assembly from the rear trailing arm assembly.

    2. A01NG7QE01
      Text in Illustration
      *1 Jack
      *2 Wooden Block

      Using a jack and wooden block, jack up the rear No. 2 suspension arm assembly to replicate standard vehicle height conditions.

      CAUTION:

      Do not jack up the rear No. 2 suspension arm assembly too high as the vehicle may fall.

    3. A01NG0Z

      Remove the 4 bolts, 2 washers and rear trailing arm assembly.

    4. Slowly lower the rear No. 2 suspension arm assembly.

  11. SEPARATE PARKING BRAKE ASSEMBLY


    1. A01NDU6

      Remove the nut and separate the parking brake assembly from the rear axle carrier sub-assembly.

      Note

      Use wire or an equivalent tool to keep the parking brake assembly from hanging down by the parking brake cable.

  12. REMOVE REAR AXLE CARRIER SUB-ASSEMBLY


    1. A01NDB6E01
      Text in Illustration
      *1 Jack
      *2 Wooden Block

      Using a jack and wooden block, jack up the rear No. 2 suspension arm assembly to replicate standard vehicle height conditions.

      CAUTION:

      Do not jack up the rear No. 2 suspension arm assembly too high as the vehicle may fall.

      Note

      Keep supporting the rear No. 2 suspension arm assembly until the installation of the rear axle carrier sub-assembly has been completed.

    2. Remove the 2 bolts (A) to separate the rear axle carrier sub-assembly from the rear lower shock absorber bracket sub-assembly.

    3. Remove the bolt (B) and nut, and then separate the rear upper control arm assembly from the rear axle carrier sub-assembly.

      Note

      Since the stopper nut is used, loosen the bolt (B).

    4. Remove the bolt (C) and nut to separate the rear axle carrier sub-assembly from the rear No. 2 suspension arm assembly.

      Note

      Since the stopper nut is used, loosen the bolt (C).

    5. Remove the nut (D), spacer and rear axle carrier sub-assembly from the rear No. 1 suspension arm assembly.