HYBRID VEHICLE TRANSAXLE INSTALLATION


  1. INSTALL OUTLET OIL COOLER TUBE SUB-ASSEMBLY


    1. A01NGEYE01
      Text in Illustration
      *1 Pin
      *2 Claw

      Install the No. 1 oil cooler tube clamp with the bolt shown in the illustration.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }
    2. A01NFZD

      Install the oil cooler tube union with a new gasket.

      Torque:
      34 N*m  { 347 kgf*cm, 25 ft.*lbf }
    3. A01NEEBE01
      Text in Illustration
      *1 Oil Cooler Tube Union
      *2 Outlet Oil Cooler Tube Sub-assembly
      *3 No. 1 Oil Cooler Tube Clamp
      *4 No. 2 Oil Cooler Tube Clamp

      Temporarily install the outlet oil cooler tube sub-assembly.

    4. Install the No. 2 oil cooler tube clamp with the bolt.

      Torque:
      8.2 N*m  { 84 kgf*cm, 73 in.*lbf }

    5. Using a union nut wrench (17 mm), install the outlet oil cooler tube sub-assembly while holding the union with a wrench.

      Torque:
      34 N*m  { 347 kgf*cm, 25 ft.*lbf }

  2. INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET


    1. A01NH5A

      Install the No. 1 transmission control cable bracket with the 2 bolts.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

  3. INSTALL WIRE HARNESS CLAMP BRACKET


    1. A01NGXUE01

      Install the 2 wire harness clamp brackets with the 2 bolts.

      Torque:
      8.4 N*m  { 85 kgf*cm, 74 in.*lbf, (for Bolt A) }
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf, (for Bolt B) }

  4. INSTALL NO. 2 TRANSMISSION CONTROL CABLE BRACKET


    1. A01NDAN

      Install the No. 2 transmission control cable bracket with the bolt.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

  5. INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY


    1. Make sure that the knock pins are installed on the engine.

    2. A01NE62E01

      Install the hybrid vehicle transaxle with the 10 bolts shown in the illustration to the engine.

      Torque:
      Bolt A
      64 N*m  { 653 kgf*cm, 47 ft.*lbf }
      Torque:
      Bolt B
      46 N*m  { 469 kgf*cm, 34 ft.*lbf }
      Torque:
      Bolt C
      64 N*m  { 653 kgf*cm, 47 ft.*lbf }
      Torque:
      Bolt D
      43 N*m  { 438 kgf*cm, 32 ft.*lbf }

      Note


      • Do not reuse bolt B.

      • Do not forcibly pry on the hybrid vehicle transaxle assembly.

      • Do not apply grease either to the splines or to the input shaft.

      Bolt Installation Direction Diameter Bolt Length
      A From transaxle to engine 12 mm (0.472 in.) 55 mm (2.17 in.)
      B From engine to transaxle 10 mm (0.393 in.) 41 mm (1.61 in.)
      C From transaxle to engine 12 mm (0.472 in.) 65 mm (2.55 in.)
      D From engine to transaxle 10 mm (0.393 in.) 33 mm (1.30 in.)

  6. INSTALL HYBRID TRANSAXLE MASS DAMPER


    1. Install a new gasket and the hybrid transaxle mass damper.

      Torque:
      39 N*m  { 400 kgf*cm, 29 ft.*lbf }

  7. INSTALL AUTOMATIC TRANSMISSION CASE COVER


    1. A01NER9

      Install the automatic transmission case cover with the 2 bolts.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

  8. INSTALL FRONT ENGINE MOUNTING BRACKET


    1. A01NEVK

      Install the front engine mounting bracket with the 3 bolts.

      Torque:
      64 N*m  { 653 kgf*cm, 47 ft.*lbf }

  9. INSTALL NO. 3 AUTOMATIC TRANSMISSION CASE COVER


    1. A01NE13

      Install the No. 3 automatic transmission case cover with the 2 bolts and clip.

      Torque:
      8.4 N*m  { 85 kgf*cm, 74 in.*lbf }
    2. A01NCOI

      Install the No. 3 transmission control cable bracket with the bolt.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

  10. CONNECT ENGINE WIRE


    1. Connect the 4 connectors and 8 wire harness clamps to the hybrid vehicle transaxle.

      A01NFS0

  11. INSTALL MANIFOLD STAY


    1. A01NCST

      Install the manifold stay with the bolt and nut.

      Torque:
      Bolt
      34 N*m  { 347 kgf*cm, 25 ft.*lbf }
      Nut
      35 N*m  { 357 kgf*cm, 26 ft.*lbf }

  12. INSTALL FRONT FRAME ASSEMBLY


    1. A01NFUZ

      Install the engine mounting insulators RH and LH with the 2 nuts.

      Torque:
      95 N*m  { 969 kgf*cm, 70 ft.*lbf }

    2. Install the HV transaxle mass damper with the bolt.

      Torque:
      14 N*m  { 138 kgf*cm, 10 ft.*lbf }
    3. A01NE5M

      Install the front engine mounting insulator with the nut.

      Torque:
      87 N*m  { 887 kgf*cm, 64 ft.*lbf }
    4. A01NDCA

      Install the rear engine mounting insulator assembly with the 2 bolts.

      Torque:
      75 N*m  { 765 kgf*cm, 55 ft.*lbf }
    5. A01NE2D

      Connect the engine wire with the 2 clamps.

  13. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

    Tech Tips

    Refer to the procedure from Install Engine Assembly with Transaxle Click here.